Question about BMW 318

Open Question

Clutch master cylinder diagram for 1985 bmw 318i

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1985 bmw 318i starts but

try cleaning the idle speed control valve & throttle body with brake cleaner

Posted on Oct 13, 2008

Ad
  • 10 Answers

SOURCE: ford focus st170 clutch master cylinder

To replace the clutch master, you must remove the under hood fuse box and air filter housing assm, then remove the hydraulic line that goes into the inlet port of the clutch master, then inside the car, remove the hush panel/knee bolster panel from under the steering column, and loosen the boilts that retain the brake pedal to the firewall, then remove the two 10mm bolts that secure the clutch master to the brake pedal assm. Reverse procedure ti install, then fill the brake master cylinder with clean fluid, loosen the bleeder screw at the top of the trans, and bleed the clutch as you would the regular brake system, but never pump the pedal, tighten screw, with foot off of clutch pedal open screw and press pedal to floor, then tighten screw before you release pedal, then release pedal loosen screw, etc. until no more air comes out, it may take quite a few times to fully bleed the system.

Posted on Feb 07, 2009

motor1258
  • 6674 Answers

SOURCE: remove master clutch cylinder on 1992 bmw 325i

Perhaps this link will be of some help.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004a3c7

Posted on Feb 18, 2009

  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

  • 2 Answers

SOURCE: problems with clutch master cylinder on a suzuki

I too am having problems with my 2006 GV clutch master cylinder. I noticed gradually over several weeks the gears and clutch pedal were degenerating and then the cluth gave completely. My mechanic took a look around and said the cylinder is the cheapest one he has ever seen, it's just a piece of plastic apparently! Is going to hopefully get the part this week or next, though he said as it's such a cheap and nasty part its likely it will happen again in the future. Not happy!

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I bleed a clutch for a 1985 mazda rx-7


Your clutch slave cylinder could be bad and leaking,here's a picture of it,it's bolted to the side of transmission,has a bleeder screw on it for bleeding.Normally,your fluid shouldn't be low,here's how to replace.

Jan 30, 2013 | 1985 Mazda RX-7

1 Answer

Over 2 year period either the clutch master cylinder or lines or slave cylinder has literally blown up from pressure--why? 1985 f-250 7.6 l


Sounds like clutch is too hard to release causing excessive pressure. Could be binding release bearing or faulty clutch.

Aug 10, 2010 | 1985 Ford F 250

1 Answer

I have a 1985 Chevy S-10. I have not started or drove this vehicle for a few months. I go to start it today and the clutch goes all the way to the floor with no resistance. Please help?


Your S10 has a clutch master cylinder and slave cylinder, a hydraulic clutch system.

You need to fill the master cylinder and bleed both the master and slave cylinders in order for the clutch mechanism to work properly.

Dec 27, 2009 | 2001 Chevrolet S-10

1 Answer

REPLACE WINDSHIELD WIPER ARM ON 1985 BMW 318I


If you buy a new set of w/blades it will tell you on the back of the box ..
So go into the spare parts in any car spares and look for the box turn it over and read all instructions and you can do it your self in 20 minutes.
Have a goodday RON

Nov 14, 2009 | 1985 BMW 3 Series

1 Answer

1985 bmw 318i wiper fluid system won't work. i would like a diagram to check out the problem.


If the pump is working then the nozzles are probably clogged. Either remove and soak in a calcium rust remover or replace.
Also you might want to chace the hose from the tank and make
sure it's not clogged or kinked.

Apr 03, 2009 | 1985 BMW 3 Series

1 Answer

On a 1985 318i bmw my o2 censor was cut in half and i cant find the other other side need a wiring diagram


If I remember correctly, the original plug connector location is by the battery. It is a small round black plug.

Mar 07, 2009 | 1999 BMW 318 ti

1 Answer

Wired


HERE IS A SITE WITH A LOT OF WIRING MANUALS. LOOK ON THE BOTTOM RIGHT OF THE
PAGE FOR THE AUTO MANUALS.
http://wedophones.com/ManualsLead.htm

Oct 14, 2008 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...