Question about 2000 Jeep Grand Cherokee

Open Question

2000 jeep grand cherokee. Intermitantly all gauges and some of the overhead console displays go to zero or dashes. Also the key chip sensor doesn't see teh brand new programmed key, but the car still runs fine. Doesn't seem like the cpu is faulty because the car runs fine. Seems like a bad ground to me. Any suggestions where to locate the ground wire in question?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Key gauge lights up and stays lit while other gauge lights go off/on intermittently. Jeep seemingly runs fine, power windows work, radio works. What to do!


If it is a warning light shaped like a door key, it could be the warning light for the security system. Its telling you there is a problem with the chip in your key or the sensor in the lock cylinder.
Your owner's manual should show all of the warning lights and what they mean.

Dec 18, 2012 | 2000 Jeep Grand Cherokee

1 Answer

What fuse is for the power door locks on a 2000 Grand Cherokee Laredo?


Check position F8 15AMP (Lt Blue) for Overhead console, rear wiper, IP lights, rear flipper glass solenoid, POWER LOCKS (click for zoom)...

zjlimited_779.jpg

This is located WJ Junction Block (under dash, left of steering wheel)...

zjlimited_780.jpg

Hope helps (remember to rate this answer).

Mar 03, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I have a 1996 grand cherokee. engine cranks but wont start. getting nothing on dashboard gauges and getting nothing but dashes on overhead digital gauges except temp. recently had new alternator put on. is...


More than likely needs a crank sensor, Try cranking with the crank sensor disconnected, you should not get the dashes in the cluster. The crank sensors take out the communication system of the vehicle

Jul 20, 2010 | 1995 Jeep Grand Cherokee

1 Answer

We have just service our 1998 Jeep Cherokee Larano as per the service schedual I cant get rid of the service now off the dash, how can I remove this & reset for the next service


If it has a service indicator light in the middle of the dash then try this;

1. Turn the ignition to the run position but do not start the engine.

2. Press the "Set" button until "0 Miles To Service" is displayed.

3. Then hold the button just below the "Set" button down until "3000" is displayed.

On some applications you might also have to hold the "Set" button down.

If you have an overhead console computer try this;

1. Turn the ignition to the run position but do not start the engine.

2. Press the "Step" button until you see Zero Miles To Service displayed.

3. Then press and hold "RESET" until the display resets.

May 17, 2010 | 1996 Jeep Grand Cherokee

1 Answer

How to remove Overhead Console on 2000 Jeep Grand Cherokee, due to menu bottons not working


straight from the Jeep service manual

1.) Disconnect negative battery cable.
2.) Remove screws attaching front of overhead console to front of bracket.
3.) Pull console downward from area near courtesy lights. 4.) Disconnect electrical connectors and remove console from vehicle.

To install, reverse removal procedure.

Apr 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2002 Jeep Grand Cherokee. The overhead console display works intermitently? It does seem to come on (after switching the ignition off and on again) after the vehicle warms up a few minutes? Any ideas?


This is a very common problem with many of the mid 2000 truck and SUV overhead consoles. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Mar 04, 2010 | 1999 Jeep Cherokee

1 Answer

Oil change


good morning and welcome to fixya.com. do you have an oil change light on that you are trying to reset or do you just want to set the minder on the computer in the overhead console. if its just the overhead console then go to where you want to and hold both buttons in until you hear a beep then the numbers will reset to zero for you along with you fuel mileage and economy gauge. good luck and let me know the outcome.

Mar 07, 2009 | 1996 Jeep Grand Cherokee

1 Answer

2002 Jeep Grande Cherokee overhead console has no display


try unhooking the battery to see if resetting the body computer helps. low batteries and poor connections at the battery can cause weird problems like this

Oct 15, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...