Question about Acura Integra

Open Question

Locating wiring harness for the o2 sensor for 01 acura integra

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 92 Acura Integra is not starting could it be my transmission fluid level

Search Results

    "No start" Due to Failed Fuel Pump Relay : Acura Integra ... > Problems > Acura > Integra
    where is the fuel system relay located at?I have replaced the distributer 2 times and also the... 1992 Acura Integra. fuel pump???? The car does not start unless I ...

    92 Integra wont start! Very weirdo problemo... - Honda-Tech
    Jun 13, 2012 - Re: 92 Integra wont start! Very weirdo problemo ..... 91 Integra LS Defroster/Water Leaking, Bigmo5328, Acura Integra, 8, 01-30-2014 12:14 PM.

    92 DA9 WILL NOT START!!! - Team Integra Forums - Team Integra > ... > Generation Specific > Generation Two

    Apr 5, 2010 - 11 posts - ‎9 authors
    I just bought a 92 integra with the B18A1. The guy I ... is the premierAcura Integra Forum on the internet. ... But it still won't start and I don't know what is up. .... Engine will not rotate when attempting to start 98 gsr cranks but won't start. - Team Integra Forums ...
    10 posts
    Feb 9, 2012
    1992 Acura Integra NO SPARK! - Team Integra Forums ...
    15 posts
    Feb 5, 2012
    92 integra wont start after driving - Team Integra ...
    15 posts
    Oct 17, 2010
    Car wont start! has fuel but lil spark..? - Team Integra ...
    15 posts
    Dec 1, 2008
    More results from

    My '92 Integra cranks but does not s

Jan 21, 2016 | Acura Cars & Trucks


How to Test the O2 Sensor of Acura Integra car?

O2 sensor needs to be replaced when you get low gas mileage in car.
So before replacing the sensor it needs to be tested.
The procedure to test O2 sensor is as follows: ---
1) First drive the vehicle for 15 minutes in normal temperature.
2) Then Stop the vehicle in park mode and turn the engine off.
3) You will see primary O2 sensor on the exhaust manifold, the manifold will be very hot to touch so take care.
4) The function of O2 sensor in the car is to measure the amount of oxygen in car and then send that information to engine to adjust fuel pressure.
5) Now to measure the O2 sensor reading. Carefully disconnect the wire at the O2 connector, and hook the positive lead of volt meter to the O2 sensor side of the connector and connect the positive lead of volt meter to harness side of the connector.
6) In the O2 sensor you will notice two black wires that are not used for testing.
7) Now before beginning the important part of the testing procedure, check out properly that wires of O2 sensor and wires of volt meter are not getting touch to any other metal part or the manifold.
8) After checked and confirmed. Now start the car and see the voltage in engine idle position.
9) The reading will go high or go low but the average reading that it should show is 500 mV.
10) Now let the engine run and with engine running disconnect the fuel pressure regulator vacuum hose, and plug the hose with your finger.
11) The 500 mV reading will go to 700-800 remove the finger the reading will fall low to 300 mV.
12) But if these readings are not showing properly that indicates the fault in the sensor.
13) The secondary O2 sensor is located after the catalytic converter. The procedure to measure secondary O2 sensor is exactly the same like how you measured the primary O2 sensor.
14) The secondary oxygen sensor is located under the car.
15) Put the car on jack stands on the rack, this will give you proper sensor location in the car.
16) You can test secondary O2 sensor to conform the fault before replacing the O2 sensor.
17) The cost of replacing the O2 sensor is near to $100.This cost is for if you do it yourself.
This will help. Thanks.

on Mar 22, 2010 | Acura Integra Cars & Trucks

1 Answer

O2 sensor wiring diagram

You never use a Universal Oxygen Sensor & have to solder it in

Makes no sense

Buy an NTK from Rock Auto.Com & just plug it in

Front # 24169
Rear # 24546

Mar 28, 2014 | 1996 Acura Integra GS-R

1 Answer

P0135 o2 sensor geo p0141 po300 po141

Po 300 could be many things,plugs wire,coils,sensors,catalityc con.

Jun 03, 2013 | 1997 Acura Integra

1 Answer

Replacing stock oxygen sensor on 01 acura integra gsr with bosch oxygen sensor color matching chart is wrong

get OEM O2 sensor and not a universal, then there is no need to cut wires just clip it on. you can go right to Honda and the will sell you one

Mar 16, 2010 | 2001 Acura Integra

1 Answer

Where is the o2 sensor on a 1998 Acura Integra?

if its not located on top of the headers, follow the exhaust back and look for what looks like a wire going into the exhaust.

Feb 06, 2010 | 1998 Acura Integra Type R

1 Answer

Check engine comes on every times i drive my 1993 acura integra gsr

you need to get the code checked from the ecu using an OBDII scanner, otherwise the information you have given cannot be used to diagnose the problem.

The check engine light comes on if any of the car's sensor's are faulty or do not respond to the ecu.

If the car drives perfectly even though the light comes on, the likely problem is the o2 (lambda) sensor on the header or cat, which causes a CEL but no ill running effects.

Go to a garage who can pull the codes off the ecu then look up the code on the integra or honda forums and take it from there.

Oct 23, 2009 | 1993 Acura Integra Hatchback

2 Answers

Have code p1399 on a 1999 acura integra 1.8 dohc

P1399- Acura = Random/Multiple Cylinder Misfire Detected

Acura forums state that It could be a coil pack or O2 sensor, or EGR.

Sep 18, 2009 | 1999 Acura Integra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides