Question about 2005 Chrysler 300

1 Answer

How much should it cost to replace a bad egr valve for a 2005 chrysler 300c

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

An EGR valve is simple enough to replace. The part alone costs roughly $90.
It is located at the back of the engine.
If you take a look, there will be a Iron rod going from the back of your intake manifold ... downwards ... its going to the EGR Valve.

Cheers,

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

300c egr


a picture is worth 1000 words if you need further help let me know. pull the cover and you will see ita64d789.giff20b445.jpg

Oct 22, 2008 | 2005 Chrysler 300

1 Answer

P0404 chrysler 300 - 2005


Trouble Code: P0404

EGR Position Sensor Signal Performance

Possible Causes:


EGR Sensor signal circuit is open or shorted to ground.EGR Sensor 5v supply circuit is open or has high resistanceEGR Sensor ground circuit is openEGR solenoid control circuit has a problem.EGR valve actuator loose, sticking, blocked or improperly grounded.EGR Sensor is damaged or has failed.Intermittent condition.PCM has failed.Hi Sherry,here is a link to the EGR valve,easy to remove,just disconnect electrical connector and remove both bolts.

Feb 11, 2013 | Chrysler 300 Cars & Trucks

1 Answer

Error code P0406 & P2008. Any suggestion


by dillardw I had the code po406 in my 2005 chrysler town and country. I is problem in the EGR valve. I replaced the EGR valve. the valve is by the alternator on the 3.3L engine and has a tube going up and into the intake manifold on top of the engine. The valve cost $ 65.00 in 2008 at the dealer with discount it was cheaper than two after markets that i checked. I erased the dtc from the computer and have had no more problems with this. Of course the problem could be different on your vehicle. I hope this helps.

Jun 21, 2011 | 2005 Chrysler Town & Country

1 Answer

How do you replace the egr valve on a 300


Heat up the exhaust pipe to egr with torch and spray with knockitloose or wd40 when not hot. Then remove that pipe. Then remove vacuum hose and the 2 bolts that hold it on.

Mar 31, 2010 | 2005 Chrysler 300

1 Answer

2005 chrysler 300c. The pedal is to the floor


if it is an automatic ( speed sensor mentioned ) check the gear linkage selector /cable for proper adjustment as it may not be selecting correctly into drive

Mar 21, 2017 | 2005 Chrysler 300

1 Answer

2005 t/c touring...problem is o.b.d. liht stays on i did the ignition test of on off three times and i get these codes...... p0404 -------p0406


check ur egr valve circuit the wiring and connections for damage or loose if good check and test egr valve possible carbon build up clean with carb cleaner to free valve or egr has gone bad and needs replacement

Mar 08, 2010 | 2005 Chrysler Town & Country

2 Answers

Code P0406


Where is the egr valve on my crystler 300?

Apr 10, 2009 | 2005 Chrysler 300

2 Answers

Engine Light On - 2006 Chrysler 300 3.5 engine


I have a 2005 Chrysler 300. The engine light comes on from time to time -- sometimes it will stay on for a week or so and then go off for at most a day or two. I had the code read yesterday and the feedback was "EGR pressure flow is low." My car has about 65K miles. Is this a typical problem with this car? I was told replacing the EGR valve would fix the problem. How easy is it to replace an EGR valve on this vehicle? Once replaced, do I need to reset the computer --- if so how do I do this? If it is easy to fix, could you please provide step by step directions and show me location of the part in question that needs replaced?

Mar 30, 2009 | 2005 Chrysler 300

1 Answer

Code P0406 egr valve faulty needs replaced


well,if you know how to install the egr valve,i recommend doing it youself because the part is NOT covered under dealer warranty.i have an 05 300 limited and had this work done.the total cost will be between $480 - $600 dollars at the dealership.if you know a competent mechanic,take it there instead.the part cost around $200 dollars.

Jan 10, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
2005 Chrysler 300 Logo

994 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...