Question about 1991 Eagle Talon

Open Question

My 1991 eagle talon check engine light will come on sometimes and then the car will seem like it is running on 3 cylinders,then after i let it sit for a while with the engine off i will start it up later on and the light will be off and it runs just fine.. any ideas ?? thanks.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 eagle talon wont rev past 2500rpm


May not be getting enough fuel to the engine

Mar 16, 2013 | 1991 Eagle Talon

1 Answer

1993 eagle talon es with 2.0 dohc engine and 5 speed manual transmission there are only 2 cylinders working 1 and 4 are good but 2 and 3 dont work wht can i do


So i think you have 2 ignition coil packs on your car, each one connects to 2 cylinders.
But i dont know what cylinders each one controls, but the coil connected to cylinders
2 and 3 may have gone bad. Thats where i would start. If you check and find out that
one coil pack connects to cylinders 2 and 3, remove the coil packs and switch their positions.

Reconnect the wires and see if then cylinders 2 and 3 work, and 1 and 4 dont. That would tell
you whether that coil pack is bad. Thats seems most likely to me.

Sep 28, 2011 | 1993 Eagle Talon

1 Answer

I wash the engine and run 2days. NOW DONT START. I PUT A NEW COIL. THE CAR DONT HAVE SPARK FIRE.


The cam angle sensor is located on the left of the cylinder head, you could have damaged it while you were cleaning the engine. To check it, disconnect the hardness connector for the camshaft position sensor, turn the ignition key to ON and measure the supply voltage on terminal number 3, it should be about 12v, Then check terminal 2 on the harness side for signal voltage, it should be 4.8 to 5.2 volts.

Apr 13, 2011 | 1991 Eagle Talon

3 Answers

Firing order for a 1991 eagle talon


info and printed diagram available at your local auto parts store

Sep 07, 2010 | 1991 Eagle Talon

1 Answer

Where is knock sensor on a 1990 eagle talon


The knock sensor is located in the engine valve or cylinder at the back of the motor or it can be located in the intake manifold close to the point where it connects to the engine block.

Dec 05, 2009 | 1991 Eagle Talon

1 Answer

Reving up to 3000 rpms from idle


Check all your vacuum hoses especially the larger ones like the one from the brake booster to the intake. Check them for cracks of see if they're broken. Also spray WD-40 or carb. cleaner on the intake manifold where it meets the cylinder head. If the idle changes, you have a vacuum leak there.

Feb 03, 2009 | 1991 Eagle Talon

1 Answer

What causes my 1991 eagle talon engine to run rough?


if the emissions control didnt check the egr valve check that. otherwise the idle air control motor/servo. also look for vacuum leaks.

Nov 20, 2008 | 1991 Eagle Talon

Not finding what you are looking for?
1991 Eagle Talon Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Stewart Dibbs

Level 2 Expert

322 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...