Question about Ford GT

Open Question

Can sump be removed with engine still in engine bay

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set old pump to remove and install in another Toyota same motor


remove all of the sump bolts
use a paint scraper or flat blade to break the adhesive sealant used in engine assembly
remove the sump
get a sump gasket kit and clean the sump and block
use loctite red and install the sump and gasket

Oct 24, 2017 | Toyota Cars & Trucks

3 Answers

I have a 2001 chevy astro van, all wheel drive. How do you change oil pan no one has a book for it


looks like a tough job ahead

taking the sump off ?...motor in the engine bay

could try undoing plenty and lift the body up

if you cant get clearance under neath with motor in the engine bay
motor will have to come out


if trying with motor in the engine bay
lots of drive train in the way ..
undo engine mounts
support the motor .... even lift motor a bit
for clearance from steering gear and chassis ,suspension etc
to get the sump off



cant tell if it covers AWD
2001 Chevrolet Astro Manuals



26348193-zlfniwo0dqdptnnvitgctddr-5-0.jpeg

26348193-zlfniwo0dqdptnnvitgctddr-5-1.jpg

26348193-zlfniwo0dqdptnnvitgctddr-5-3.gif

Nov 09, 2016 | 2001 Chevrolet Astro

1 Answer

Nissan oil capacity QD32


Cut the side out of a 10 litre oil container to catch the used oil.
Use a plastic shopping bag around the filter to catch most of the oil when you maneouvre the filter out of the engine compartment. About 6 liters new oil, diesel 15w40 dino oil is what I use to refill both sump and oil filter, about 5.3 in sump, the rest in the filter. Run engine and then recheck on dipstick after engine has been stopped for 5 minutes to allow drain back to sump.great thing is that you don't have to jack up the vehicle to get under it just to do the oil, but it makes it easier to do the filter if you remove the left front wheel and go through the rubber side curtains between the wheel well and the engine bay to get to the filter, especially if the engine is hot.

Jul 08, 2014 | 2005 Nissan Terrano 2.7

2 Answers

Remove sump


sump what sump.
are you asking an engine question?
what is wrong?, tell the story, or at least a tiny hint so we can get on the same page..
my wild guess is the engine oil pan (sump) and not tranny or other
sump like objects. or other many fluid containers all very sump like.
but the answer is in the FSM, buy one, and read how to remove anything on the car.
here state side we have alldata.com and dont need books until
we break 10 parts and then read the authortive manual.

May 20, 2014 | 2009 Chevrolet Captiva 2.0D

1 Answer

WHAT TO LOOK FOR IF THE IS ENGINE LEAK


I'm presuming an oil leak?

Check around the sump where it bolts to the bottom end. Visually inspect the sump for holes (altho you would be losing oil pretty severly if there is). Check around the oil filter, might not be sealed right.

One way to narrow the leak location is get a sheet of card and put it on the ground under the engine bay overnight. It should show you where the oil is dripping from or what its dripping off.

Also Accents have a habbit of dropping oil level very quickly when they are getting close to requiring an oil top up.

Dec 05, 2012 | 1999 Hyundai Accent

1 Answer

What are the steps in changing the oil in a 1986 Lincoln Town Car


1) Purchase appropriate oil filter, sump drain bung washer and chosen engine oil.
2) Prepare an oil pan, sump bung wrench and oil filter removal tool (check access to oil filter to be sure that your tool is suitable.)
3) Run the engine until its warm to hot.
4) With the car jacked up and secured, remove engine oil filler cap and remove engine oil sump drain bung and allow oil to flow out into your drain pan. Keep an eye on your oil and make sure it doesn't overflow from your drain pan.

5) Refit sump bung with new washer and tighten. Do not over-tighten, and be especially careful when tightening into an alluminium sump.


6) Remove oil filter. Oil will flow out from this filter when removing, so your drain pan will need to be under the filter housing when removing.


7) Run a smear of clean engine oil around the filter rubber seal and refit new filter. Tighten hand tight only. Do NOT crank this filter super tight as you may damage the rubber seal and even the filter casing which can impede oil flow.


8) Refill engine with proper quantity of oil. If you cannot find how much oil your engine is supposed to take, then refill with the same quantity of oil which you drained out.


9) Restart the engine while checking the oil pressure warning light on the dash. The warning light may stay on for three or four seconds and then go out. If this light stays on for longer, then stop your engine and check for oil leaks at the filter body and sump drain bung.


10) Once the engine oil pressure warning light is off after starting, stop the engine and check the engine oil level (with vehicle on the flat and off any axle stands.)


11) Road test the vehicle, driving it for a mile or two before re-checking for oil leaks under the engine bay and engine oil quantity.

Nov 04, 2012 | Lincoln Cars & Trucks

1 Answer

Need step by step guide on how to service a toyota yaris


Firstly look at the part numbers of the items you want to replace, oil filter, spark plugs, if you want to put new ones in, air filter and if the car has quite a high mileage, the fuel filter. The fuel filter is under the car and looks like an alumimium cylinder. If you go to a quality spares shop they can sell you reputable parts, often for a lot less than Toyota original parts. Ask them to set the gaps on the plugs and buy a gallon of the type of oil that is specified in your handbook for your type of climate. You will also need a sump plug washer.

The first thing to do would be to remove the air filter from the cleaner. This is usually held together with clips and/or screws. Clean out the inside of the housing and place the new filter in the same position as the old one. Clip and screw everything back together and that job is done.

Blow around the spark plug holes, number each spark plug lead from 1 (front of engine) to 4 (back of engine). Remove the plug leads and the unscrew the plugs. Replace with the new plugs being careful not to overtighten them and replace the plug leads onto the correct plugs.
Check your engine coolant level and top up if necessary.
Start the car and get it to normal temperature. Switch off engine. Chock the wheels, put the car in park or gear and handbrake on. Jack up the drivers side giving you enough space to slide a bucket under the engine. DO NOT GET UNDER THE CAR. Wipe around the sump plug and SLOWLY undo it. The plug is at the bottom of the sump at the lowest part of the engine. THE OIL ON THE OTHER SIDE OF THE PLUG IS HOT SO TAKE CARE. Let the oil drain. Whilst this is happening, wipe around the filter base and unscrew the filter. This will also be hot and oil will spill so make sure that the bucket can also catch the spillage. Wipe away any excess oil and make sure that the rubber seal has not been left on the engine. It is important to remove it. Place a smear of new engine oil on the new filter rubber seal and screw the filter in place. A good hand tightening is enough. By now all the oil will be out of the engine and you can replace the sump plug washer and screw the sump plug back into the sump making sure it is tight. Wipe away any loose oil. Remove the oil filler cap and pour about half the oil into the engine. let it settle for a minute and remove the dip stick, clean it off, and dip it again. You should see the oil level near the bottom of the dip stick. Add another pint and check again. Keep going until you reach the full mark. Replace the oil cap and dip stick and start the engine. Run it for a few minutes and check the filter and sump plug to make sure they are not leaking. Switch off, let the oil settle and check the level again. It will go down because the filter is now full. Top up and you are done. Look around the engine bay to make sure nothing is amiss. If the car has done about 20 000 remove the wheels and check the brakes have enough lining. Check the tyres for tread, cuts and so on. Make sure all your lights are working. Now you are pretty much good to go.

Feb 16, 2010 | Toyota Yaris Cars & Trucks

1 Answer

HOW DO YOU REMOVE THE OIL PUMP ON 2003 PASSAT?


It's a difficult job requiring the engine to be hoisted above the engine bay so the sump can be removed to gain access to other parts needed to be removed before doing the pump removal.

Jan 22, 2010 | 2003 Volkswagen Passat

1 Answer

Removing a sump pan


you drain as much engine oil from them sump as you can by undoing the 13mm sump plug. you then undo all the bolts holding the sump onto the engine

Jul 24, 2009 | 1996 Ford Escort 4 Door

1 Answer

HOW TO REMOVE SUMP ON ZETEC 1.6 FORD STAITIONWAGON ,98 MODEL


undo engine mounts and jack engine up a bit,cheaper to find a complete engine in scrapyard and change it if its endy.this is often cheaper than a repair

Apr 11, 2009 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...