Question about 2004 Jeep Wrangler

1 Answer

2004 Jeep Wrangler cleaning out cats...Will this make the motor run bad???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Cleanig them? with a fuel system cleaner system? that would be ok. if need to be done correctly to burn it all out. if you want to hollow out the cat...do not. it will effect the jeep running and will set the eninge light (also kill the red eyed tree frog and stuff lol) maybe you can clarify what you want to do, if this does not answer your question.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

04 jeep wrangler 4.0 engine auto trans, hesitates after driving 50-60 miles at traffic lights.


Hesitation is usually a dirty throttle body and idle air control motor.

Oct 02, 2016 | 2004 Jeep Wrangler

1 Answer

2004 jeep wrangler tj my dash lights and running lights arent working the fuses are good what else could it be


There are fusible links which could fail, usually in the wiring from the battery + or located near the starter motor. Also possible you have a bad light switch. Use a voltmeter to find this.

Dec 12, 2014 | 2004 Jeep Wrangler

1 Answer

My Jeep will run, but it misses and backfires and will not accelerate. It has a new computer, new fuel pump, new spark plugs and the timing is right. What else could it be?


was the computer programed??, also how about the crank sensor, then the next thing is to check for a bad cat, you may have a clogged cat converter that restricks the exhaust flow,and last is the o2 sensor. have your computer scanned for any codes.

Apr 16, 2010 | 1997 Jeep Wrangler

2 Answers

'88 Wrangler w/4.2 & Auto Trans. Cat Convert


The jeep has air injection and this is part of the air pump. The cat should have two ports.. These tubes should have check valves to prevent backfire.Usually their routed up on both sides of motor and attached at the air cleaner abouts

Nov 05, 2009 | 1988 Jeep Wrangler

3 Answers

1998 jeep wrangler starting problems


There are several things you can do if you haven't done so already, Check voltage at ignition coil, as soon as the engine starts to turn over there should be voltage. If not, the crank sensor is not triggering the ECM quickly.... on 98-99 wranglers, this was a problem area. Check terminal connectors at the ECM, clean and secure, another area of concern.The module on the side of the throttle body is the air idle control 'motor' as jeep calls it. Over time they tend to carbon up and it results in bad air/fuel mixture and yet fails to send a fault code, you can remove & clean also the O2 sensor in front of the cat. convertor.remove & clean. Check fuel pressure, you should have some residual PSI. Treat fuel system with a good treatment...I like the Lucas products, their fuel system treatment and injector cleaner burns hot & clean.
I hope these suggestions help...and the wrangler returns to top form...good luck.

May 14, 2009 | 1998 Jeep Wrangler

1 Answer

My 2004 jeep wrangler 4 cyl SHAKES only when i turn on the AC ???


mcdevito75 here, When the A/C is on it"s an extra load on the engine, the cars computer sends a message to the high idle sensor to increase the engine speed to handle this extra load. The sensor or motor device used on your car to increase the engine speed is not working, have your local repair shop run a scan on your computer and Idle system.

Mar 16, 2009 | 2004 Jeep Wrangler

1 Answer

Jeep Blower Motor


The blower motor squirrel cage blower wheel must be rubbing inside the blower case or something is in there like leaves..

Jul 07, 2017 | 1997 Jeep Wrangler

1 Answer

2004 Jeep Wrangler died out while running, wont start now.


IF ITS A 4.0 L THE THROTTLE BODY MAY JUST NEED TO BE CLEANED, AS FOR A SENSOR ITS POSSIBLE BOTH THE CAM AND CRANK SENSORS ARE GARBAGE ON THAT VEHICLE I CHANGE THEM ALL THE TIME

Dec 16, 2008 | 2004 Jeep Wrangler

1 Answer

2004 Jeep Wrangler Solenoid


THE SOLINOID VALVE IS ONLY PART OF THE SYSTEM YOU MAY HAVE A LDP (LEAK DETECTION PUMP) PROBLEM INTERNAL LEAKS ARE HARD TO DIAG YOU MAY WANT TO BRING TO A DEALER.

Nov 26, 2008 | 2004 Jeep Wrangler

2 Answers

2004 jeep wrangler


Clean the inside of the MAF sensor with MAF sensor spray, it is made bt CRC.

Oct 20, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2004 Jeep Wrangler Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...