Question about 2001 Hyundai Elantra

1 Answer

My car is not starting cuase the clutch is stuck and all the way down and olso the stick shift stuck in rear position i drove my normal last night and it was very good by the way ichange the clutch and evrything 6 month ago please can y tell me its hidrolic clutch padel or somthing elss THANK YOU

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 600 Answers

It sounds like the master cylender has failed, maybe old, damp fluid has corroded the bore and ruined the rubber seal, joggle the car to unload the gears and it will come out of gear (and perhaps roll away, is the e brake ok and on?)

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long does a clutch last


hi, i take it your vehicle is a manual or stick shift, to check your clutch you use 4th gear and with the engine running drop the clutch to see if it either stalls out the engine or slips. if your clutch cable is broken you will need to repair that first. with engine off engage first gear and attempt to start it, make sure there are no children or animals close to the vehicle, if the clutch is ok with your pedal pushed down the car will start, otherwise it will crawl at a very slow speed, needing repair.

Jun 20, 2014 | Suzuki Swift Cars & Trucks

1 Answer

Car sometimes wont start even if just turned off replaced starter motor and ignition barrel


Try starting it with the shift lever in neutral, if it starts, the transmission switch is bad (automatics), or with the key to start position move the shift lever thru the range of gears. If a stick shift and the clutch pedal must be pressed down, the clutch switch may be going out if intermittent starts

Apr 12, 2014 | 1989 Toyota Camry

2 Answers

1989 jeep wrangler wont shift gear and clutch gone loose


Get the clutch slave cylinder and master cylinder looked at.One of the 2 has failed.If the pedal goes to the floor or is very loose,this is very likely the cause.Not an expensive fix.Hope this helps

Jan 10, 2010 | 1989 Jeep Wrangler

1 Answer

I have a 1989 jeep wrangler. yesterday, after the stick shift felt stiff to shift, the clutch felt suddenly loose. Today, the stick shift stopped moving completely while i was driving. Finally, I was able...


Sounds like you are having a clutch problem. The sudden looseness in the clutch pedal indicates a problem with either the hydralic system, (slave or master or line) leaking or clutch pressure plate going out. Check your clutch fluid resevoir first, if low look for a leak under the vehicle, have a friend push the clutch and get underneath to find leak.

Jan 10, 2010 | 1989 Jeep Wrangler

2 Answers

1993 Ford Ranger 4.0 I put a new slave/throwout bearing in. I went to put it in gear and the stick shift is stuck in the neutral position. It won't go into any gear. When I start the truck, it is stuck...


Have an assistant push in on the clutch while you observe the function of the cluth throwout bearing lever, it may be that the throwout bearing fork lever is not on its pivot point or is out of adjustment, you should be able to rotate the rear tires when the clutch is pushed in if not the throw out bearing and fork assembly either was not put in corectly or you did not bleed out the air from the slave cylinder.

Jul 10, 2009 | Ford Ranger Cars & Trucks

2 Answers

Reverse just quit on '95 Pathfinder


If it is an automatic transmission it probably needs transmission fluid. If a standard shift check and adjust shift linkage.

Jul 08, 2009 | 1995 Nissan Pathfinder

1 Answer

Clutch wont engage.


no doubt your clutch has gone again, possibly the slave cylinder.

Mar 19, 2017 | 1999 Suzuki Grand Vitara

1 Answer

Tranny Lock


syncro problem
low on oil
check stick shift adjustments
shift stick bushes or a cable problem
check engine mounts
gearbox, fork or clutch worn

Mar 11, 2017 | 1987 Toyota Celica

Not finding what you are looking for?
2001 Hyundai Elantra Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...