Question about 1988 Jeep Comanche

1 Answer

I have a 1988 jeep wrangler when i let it sit for a little bit i have a little bit of clutch pedal but after i bleed it. theres nothing at all. Then i let it sit and it will get a little better but then i bleed and the same thing nothing. i can't get a good pedal

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 120 Answers

It sounds like a faulty clutch slave cylinder. If you cannot keep pressure, then this is where to start. bench bleed the clutch master first if possible then when installed in the car be sure to get ALL the air out then continu on from there. If no pedal still thn perhaps you have a faulty clutch and it will not allow the clutch to disengage. good luck!

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

Hello, I have 1992 jeep wrangler, i was feeling a slight sticking point half way up during the release of my clutch weeks ago and it seemed to go away. Yesterday my clutch pedal seemed to sit almost an...


Hey.This is just a long shot.The throwout bearing may be sticking.Its attached to the clutch fork and contacts the pressure plate.It slides along a shaft and the shaft may me sticking up,holding the bearing in the wrong spot.I have seen it happen.A VERY SMALL squirt of wd40 can fix it.You have to know where to put it.Not so much it gets on the clutch plate.Ask a friend or anyone that may know before you do it.This is your 1st option before you have to do any mechanical work on the car.It costs NOTHING.Check it before a workshop rips you off.Hope this helps you

Sep 21, 2010 | 1994 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

How do i bleed the clutch slave cylinder on a 95 jeep wrangler


pump up clutch pedal really fast about ten times....leave it held to floor....open bleeder on slave cyl... repeat untill you have good pedal....may need to adjust master cyl. rod on clutch pedal to get more travel....good luck....Lee

Nov 06, 2009 | 1995 Jeep Wrangler

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

2 Answers

The clutch in my 92 Jeep Wrangler suddenly stopped working.


pull the boot back on the master and see if it is wet do the same with the slave

Apr 25, 2009 | 1992 Jeep Wrangler

1 Answer

Push down on clutch pedal can't get car into gear


Likely, you have a hydraulic clutch system. Check clutch master cylijnder for fluid and leakage, check hydraulic line and slave cylinder for leaks. If fluid low or empty, bleed as you would a brake wheel cylinder. If full,have someone work the clutch while you watch slave cylinder to make sure it is moving clutch fork. If system full and little or no movement, the master may be "bypassing" internally (replace) Also, check pedal mechanical linkage. Not often but sometimes these parts can break! Could also be athat clutch itself is worn, but this does not happen overnight and you would have noted slip long before this!

Dec 29, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...