Question about 2000 Buick LeSabre

1 Answer

How to install a new blower motor - 2000 Buick LeSabre

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Its above the passengers feet , held in by 4 or5 5/16 inch
bolts .
It should drop down and out , remove the blower wheel
off the shaft , after removing the retainer clip.
reverse procedure for install.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The heater blower stopped working and the fuse is not blown?


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Feb 08, 2011 | 1996 Chevrolet Blazer

1 Answer

Air condition blower motor does not work


put in a new blower motor-
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 30, 2010 | 1999 Cadillac DeVille

    1 Answer

    How to change blowermotor on 2001 gmc jimmy


    Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

    To Remove:
    1. Remove the PCM.
    2. Remove the coolant reservoir.
    3. Remove the rear coolant recovery reservoir mounting stud.
    4. Disconnect the cooling tube from the blower motor.
    5. Disconnect the electrical connector from the blower motor.
    6. Remove the blower motor mounting bolts.
    7. Remove the blower motor insulating cover.
    8. Remove the blower motor.
    To Install:
    1. Install the blower motor.
    2. Install the blower motor mounting bolts.
    3. Connect the electrical connector to the blower motor.
    4. Connect the cooling tube to the blower motor.
    5. Install the rear coolant recovery reservoir mounting stud.
    6. Install the coolant reservoir.
    7. Install the PCM.
    W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

    To Remove:
    1. Remove the PCM.
    2. Remove the coolant reservoir.
    3. Remove the rear coolant recovery reservoir mounting stud.
    4. Disconnect the electrical connector from the blower motor.
    5. Move the PCM connectors out of the way.
    6. Remove the blower motor access cover screws. CAUTION
      Do not cut any deeper than necessary in order to remove the access cover.
    7. Cut through the access cover on the cut line using a sharp utility knife.
    8. Disconnect the cooling tube from the blower motor.
    9. Remove the blower motor mounting bolts.
    10. Remove the blower motor.
    To Install:
    1. Install the blower motor.
    2. Install the blower motor mounting bolts.
    3. Connect the cooling tube to the blower motor.
    4. Install the blower motor access cover.
    5. Install the blower motor access cover retaining screws.
    6. Using black weather-strip adhesive, seal the cut line.
    7. Connect the blower motor electrical connector.
    8. Reposition the PCM connectors.
    9. Install the rear coolant recovery reservoir mounting stud.
    10. Install the coolant reservoir.
    11. Install the PCM.
    prev.gif next.gif

    Dec 08, 2010 | 2001 GMC Jimmy

    1 Answer

    How to replace a blower motor in a 1996 ford thunderbird lx


    Removal
    1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
    1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
    1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
    Installation
    1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
    1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
    1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
    1. Install the glove compartment liner.

    Oct 07, 2010 | 1996 Ford Thunderbird LX

    1 Answer

    How to remove and install a new heater blower motor 2000 Saturn


    Removal & Installation
    1. Select the following settings:
      Turn the ignition ON Select Recirc in the OFF setting Turn the ignition OFF
    2. Disconnect the negative battery cable.
    3. Remove the wiper arm assemblies.
      CAUTION A sharp edge is revealed once the weatherstrip is removed.
    4. Remove the weatherstrip at rear of the engine compartment.
    5. Remove the cowl retaining nuts.

      7f880eb.jpg

      Fig. Remove the cowl screen assembly

    6. Remove the cowl screen assembly.
    7. Rotate the locking tabs outward to release the filter assembly.
    8. Remove the filter by lifting straight up.

      3f001dc.jpg

      Fig. Remove the wiper module retaining bolts

    9. Remove the wiper module retaining bolts.
    10. Reposition the wiper module to the right.
    11. Remove the filter housing attachment bolts.
    12. Remove the filter housing.
    13. Remove the blower motor housing:
    14. Remove the blower motor housing screws

      855cd3a.jpg

      Fig. Release the locking tabs and remove the fan housing

    15. Release the locking tabs and remove the fan housing
    16. Disconnect the blower motor electrical connector.
    17. Squeeze the bottom of the connector and pull downward.
    18. Remove the blower motor assembly by lifting straight out.
    To install:

    NOTE The fan motor assembly rib must be located into the channel in the module housing.
    1. Install the blower motor assembly into the module housing.
    2. Connect the blower motor electrical connector.
      NOTE The housing rib must fit into the slot in the HVAC module case.
    3. Install the blower motor housing. Snap the left and right clip into place
    4. Tighten the fan housing to blower motor housing screws to 9 inch lbs.(1 Nm).
      NOTE A new filter housing seal must be used whenever the filter housing is removed to prevent water from leaking into module.
    5. Remove the filter housing seal using a small flat-blade screwdriver.
    6. Install a new filter housing seal.
    7. Install the filter housing.
    8. Install the filter housing screws, and tighten the screws to 31 inch lbs.(3.5 Nm).
    9. Position the wiper module.
    10. Install the wiper module bolts, and tighten the bolts to 44 inch lbs.(5 Nm).
    11. Install the passenger compartment air filter. Notice the air flow direction indicator printed on side of the filter.
    12. Rotate the locking tabs on the filter housing inward to secure the air filter in place.
    13. Install the cowl screen.
    14. Install the cowl screen nuts, and tighten the nuts to 9 inch lbs.(1 Nm).
    15. Close filter access door.
    16. Install the weatherstrip at rear of the engine compartment.
    17. Install the wiper arm assemblies.
    18. Connect the negative battery cable.
    1. Disconnect the blower motor electrical connector.
    2. Remove the lower blower motor cover retaining screws.

      dadd8a2.jpg

      Fig. Remove the lower blower motor cover

    3. Remove the lower blower motor cover.
    4. Remove the blower motor nuts.
      NOTE Cut through the case as straight as possible because the motor cup must be replaced.
    5. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
    6. Remove the blower motor and cup from the lower case by cutting through the case between the circular ribs around the motor with a sharp utility knife.
    7. Release the blower motor retaining tab and remove the motor from the cup.
    To install:
    1. Install the blower motor into the motor cup that was cut out of the lower case.

      bc83072.jpg

      Fig. Install the blower motor (1) into the motor cup (2) that was cut out of the lower case

    2. Install the blower motor nuts, and tighten the nuts to 21 inch lbs.(2.4 Nm).
    3. Attach the service ring to the motor cup with the screws included in the kit, and tighten the screws to 15 inch lbs.(1.8 Nm).
    4. Install the blower motor and service ring into the HVAC module using the screws included in the kit. Make certain the blower motor electrical connector is pointing rearward in the vehicle, and tighten the screws to 15 inch lbs.(1.8 Nm).
    5. Install the lower blower motor cover.
    6. Install the lower blower motor cover retaining screws, and tighten the screws to 15 inch lbs.(1.8 Nm).
    7. Connect the blower motor electrical connector.

    Hope this helps (remember to rate and comment this).

    Oct 04, 2010 | 2000 Saturn Ls 4dr Sedan

    1 Answer

    How to install a front blower motor in a 96 ford explorer


    Blower Motor - REMOVAL & INSTALLATION
    (see Figures 1 and 2)

    8e5714d.jpg

    Fig. 1: Exploded view of the blower motor mounting

    ff3bdf8.jpg

    Fig. 2: Exploded view of the blower motor and wheel (fan) assembly

    Without Air Conditioning

    1. Disconnect the negative battery cable.
    2. Remove the air cleaner or air inlet duct, as necessary.
    3. If necessary, Remove the speed control module and the washer fluid reservoir.

    2587a00.jpg

    Fig. 3: To remove the blower motor, first disconnect the electrical wire harness plug...

    f234e79.jpg

    Fig. 4: ...then remove the blower motor cooling tube from the motor
    1. Disconnect the wire harness connector from the blower motor by pushing down on the connector tabs and pulling the connector off of the motor.
    2. Disconnect the blower motor cooling tube at the blower motor.
    3bbd0e1.jpg

    Fig. 5: Remove the blower motor attaching screws and the washer fluid reservoir...

    8da3ac1.jpg

    Fig. 6: ...then slide the blower motor from the housing. Take care to not damage the blower wheel (arrow)
    1. Remove the 2 screws attaching the blower motor and wheel to the heater blower assembly.
    2. Holding the cooling tube aside, pull the blower motor and wheel from the heater blower assembly and remove it from the vehicle.
    3. Remove the blower wheel push-nut and/or clamp from the motor shaft and pull the blower wheel from the motor shaft.
    To install:
    1. Install the blower wheel on the blower motor shaft.
    2. Install the hub clamp and/or push-nut.
    3. Holding the cooling tube aside, position the blower motor and wheel on the heater blower assembly and install the 2 attaching screws.
    4. Connect the blower motor cooling tube and the wire harness connector.
    5. Install the vacuum reservoir on the hoses with the 1 screws.
    6. If removed, install the speed control module and the washer fluid reservoir.
    7. Install the air cleaner or air inlet duct, as necessary.
    8. Connect the negative battery cable and check the system for proper operation.

    With Air Conditioning
    1. Disconnect the negative battery cable.
    2. In the engine compartment, disconnect the wire harness from the motor by pushing down on the tab while pulling the connection off at the motor.
    3. Remove the air cleaner or air inlet duct, as necessary.
    4. If necessary, remove the solenoid box cover retaining bolts and the solenoid box cover.
    5. Disconnect the blower motor cooling tube from the blower motor.
    6. Remove the blower motor mounting plate attaching screws and remove the motor and wheel assembly from the evaporator assembly blower motor housing.
    7. Remove the blower motor hub clamp from the motor shaft and pull the blower wheel from the shaft.
    To install:
    1. Install the blower motor wheel on the blower motor shaft and install a new hub clamp.
    2. Install a new motor mounting seal on the blower housing before installing the blower motor.
    3. Position the blower motor and wheel assembly in the blower housing and install the attaching screws.
    4. Connect the blower motor cooling tube.
    5. Connect the electrical wire harness hard shell connector to the blower motor by pushing into place.
    6. If removed, position the solenoid box cover into place and install the 2 retaining screws.
    7. Install the air cleaner or air inlet duct, as necessary.
    8. Connect the negative battery cable and check the blower motor in all speeds for proper operation.

    Hope this help (remember comment and rated this).

    Apr 23, 2010 | 1996 Ford Explorer

    2 Answers

    Chevy tahoe 1999 heater making noise when I put it on hi loud noise how do i fix it


    Remove blower motor and inspect could have leaf's or something in it, also check blower motor shaft make sure blower shaft bearing are good.

    Dec 09, 2009 | 1999 Chevrolet Tahoe

    1 Answer

    Looking for instructions or a diagram of how to install a new blower motor on 1999 chevy silverado


    1 Disconnect the electrical connector from the blower resistor
    2 Remove the blower motor insulating cover screws.
    3 Disconnect the electrical connector from the blower motor
    4 Remove the blower motor insulating cover.
    5 Pull the retaining tab down while turning the blower motor counter-clockwise in order to disengage the blower motor from the heater/ventilation module (case)
    6 Remove the blower motor. Install in reverse order.

    Feb 18, 2009 | 1999 Chevrolet Silverado 1500

    1 Answer

    Heater blower install for 1997 cadillac eldorado


    The solution is more than likely a new blower motor. Replacing this blower motor is no small task. I am in the process of doing it, but there is so little wiggle room that I suspect that if a cadillac mechanic does this job, they will jack up the engine/transaxle to make room. The motor itself is not cheap either, a replacement Delco is well over $200. I will let you know if my new motor install works.

    Oct 14, 2008 | 1997 Cadillac Eldorado

    Not finding what you are looking for?
    2000 Buick LeSabre Logo

    Related Topics:

    57 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Buick Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Buick Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...