Question about 2000 Toyota Corolla

1 Answer

Do I need to remove the brakes to change hub assembly on a 2000 toyota corolla

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 120 Answers

Yes you will have to remove the brake caliper. then the rotor. although its not necessary, some people find it easier to remove the tie rod end as well, just to allow for easier turning of the wheel. Then once the rotor and caliper are off, you will need to physically turn the steering one way or the other to access the bolts from behind the knuckle and remove them. Then repeat for all the bolts until removed. Then with a hammer, hammer on the back sid of the hub assembly, until it comes out. Please keep in mind that once the hammering starts the hub assembly might come apart so pay attention if this happens seek further help. good luck!

Posted on Aug 24, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear bearing


Remove the rear wheel, if the vehicle has rear disc brakes remove the brake caliper and brake rotor, If the vehicle has drum brakes , slide the drum off. Remove the 4 hub mounting bolts located on the back side of the backing plate.Using a hammer tap on the hub assembly (near the wheel studs) Reverse the steps to install the new hub assembly.

Jun 11, 2013 | Cars & Trucks

1 Answer

Changing the brake light lamp/bulb


the plastic posts are guides /support they just slide into place attached to lens just slide/pull the lens off

Jun 18, 2017 | 1995 Toyota Corolla

2 Answers

Hi. how would i repair a rear axle for a 2006 toyota corolla? i dont have a lift so will i need to take it to an autobody shop? if so how much do these repairs cost usually?


What are going to do to repair the axle? There really is no axle on front drive cars, the wheel assembly is connected to a hub that is mounted to the frame through swing arms. And, you would not take your car to a autobody shop for mechanical work. The cost of repairs depends on what is being done.

Nov 29, 2010 | 2006 Toyota Corolla

1 Answer

How to change front hub assembly 2002 corolla


The best way is to take the entire steering knuckle to a qualified automotive machine shop and pay them to replace the hub and bearing assembly. My local machine shop charges $65 for the hub and bearing replacement job. Although you could do it yourself, pressing out the old bearing and pressing in the new one goes much better with a hydraulic press, and there is much less chance of botching the job and ending up with a bad bearing.

To remove the knuckle, first loosen the wheel lug nuts and the center axle nut. Then, raise and support the car safely, remove the wheel, remove the brakes, and then, in no particular order, remove the center axle nut, remove the outer tie rod from the knuckle (use a puller for this), remove the ball joint bolts from the lower control arm, remove the strut bolts from the knuckle, and remove the knuckle from the CV axle spline.

When re-installing, take care that you do not damage the new bearings and seals. In particular be sure to slide the axle smoothly into the hub without making contact with the bearing or seal.

Let me know if you have any questions.

Apr 08, 2010 | 2001 Toyota Corolla

1 Answer

How to use a slide hammer to remove a stuck hub


MOUNT THE SLIDE HAMMER IN THE BOLT HOLE AND PULL OFF GENTLY

Sep 15, 2009 | 2003 Toyota Corolla

1 Answer

How to replace rear wheel hub assembly


This vehicle has Drum brakes in the rear.
Remove the rear wheel.
Remove the drum.
Disconnect ABS wire
Remove 4 bolts holding hub to axle shaft.

Sep 04, 2009 | 2003 Toyota Corolla

1 Answer

Changing front wheel hubs on a 2002 Toyota Solara - 4 cylinder


the rotors ? remove wheels and brake assembly and install new ones make sure to press the piston on the brake caliper or they wont go back on

Aug 24, 2009 | Toyota Solara Cars & Trucks

1 Answer

Corolla bearings


The front wheel bearings are pressed into the knuckle.You need to remove the axle nut,make sure to unstake the nut as to not damage the axle threads,and brake assembly,slide hammer the hub off then remove abs sensor if you have one then remove tie rod end,lower ball joint bolt and nuts,then the strut bolts.After the knuckle is off you will see a circlip on the inside by the bearing remove this then press the bearing out on a shop press.If you don't have a new hub you will also have to use a bearing splitter to get the bearing race off the hub to reuse it.Reverse process for reassembly.Hope that helps as it is not just a bolt on repair.

Nov 09, 2008 | 2006 Toyota Corolla

2 Answers

Toyota corolla


Remove wheel, brake cliper, cliper mounting bracket, brake pads and rotor.
Remove tie rod end and strut from spindle,
Remove large drive axle nut from center of hub by removing cotter pin and nut cover
Remove the ball joints 2 nuts and 1 bolt
Pull assy. lose from drive axle.
Take complete Hub assy with new bearing to an automotive machine shop and have them disassemble hub and replace bearing.
Reverse steps to reinstall

Jun 30, 2008 | 1994 Toyota Corolla

Not finding what you are looking for?
2000 Toyota Corolla Logo

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...