Question about Ford Mustang

2 Answers

Need to know what i'm missing.using '94 mustang t5 manual bolted to a 302 engine in my 1930 pickup hot rod.does the clutch fork push forward or pull back towards the cab.i don't seem to have a pivot point to see which way it should go.have no pics to see about clutch pedal to fork.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

It should pull towards the front of the vehicle.

Posted on Dec 31, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

You didn't say which clutch you are using, so I will assume that it is a 94 Mustang clutch and housing. The pivot is on the right (passenger) side, so to disengage the clutch (disconnect engine from transmission, like pushing on clutch pedal), you would need to move the fork towards the front of the truck.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I find out what make, model my 302 engine came out of ? It's in my '66 Mustang. I was told it's a '71 motor, but I would like 2 know what make, model ex (LTD, Maverick, F-100 Pickup) etc.?


Try taking the number off the engine and see if the dealer can search it up. I doubt they only put it in one car model, but the number on the engine should match the frame. Get where I'm going? As old as it is, I wouldn't expect anything though.

Apr 29, 2016 | Ford Cars & Trucks

1 Answer

How to adjust the clutch in a 1979 stock v8 Mustang for speed 302


check the push rod coming out of the slave cylinder and see if there is a threaded section of bolt into the 1/2 ball at the clutch throw out arm. If it is a one piece rod with no thread then there is no adjustment. With this application if there is a problem indicated by a slipping clutch or the pedal has to come well off the floor before engaging, the cheapest fix is to replace the clutch master cylinder as the compensating port is normally the culprit. If it is adjustable then the adjustment is with the rod pushed fully into the slave cylinder there should be about 1/2 inch between the clutch throw out arm and the 1/2 ball Worst case if you have this adjustment and the slave cylinder piston will readily return fully into the cylinder then you will have to consider the clutch

Jul 26, 2014 | Cars & Trucks

1 Answer

I have a 1965 food falcon with a mustang 302 (1978 ) v8. how do i know if it is a windsor or not?


Well there is a 302 cleveland, they are mainly an Australian engine. Identifying one is much like telling the difference between a 351 windsor and a 351 cleveland. Based on the fact that it's from Ford's 335 engine family. 8 cap screws to hold on the valve covers, the block is longer do to the timing chain housing being integrated. The fuel pump bolts are mounted vertically, and the exhaust bolt holes are diagonal. Also, a big difference between an american 302 and an aussie 302 cleveland, is the connecting rods for the cleveland are 6.000''. Where the american 302 connecting rod length is 5.090". Also, referring to a 302 as a windsor is incorrect, it's block families name is the 90 degree v8. The only engine in that family that is properly named the windsor, is the 351 windsor. The 90 degree family also includes the 302 boss. The boss has cleveland style heads, and the block has screw in freeze plugs.

Nov 27, 2009 | 2005 Ford Futura

2 Answers

I replaced ignition module and no spark still! I also did the trouble light on the neg on coil and pos on battery and no flashing on light so where do I go now?


Well, assuming that you have the light hooked up correctly ( one side on battery hot post, one on coil neg post, I'd look at the pickup assembly. That is where the module gets its signal to fire the coil. If that is no good then you won't have spark. To replace it, you will need to remove the distributor from the engine, remove the roll pin near the bottom of the stem, pull the drive gear off the stem, a few bolts at the top, and then the whole thing should just come apart. two more screws and the pickup will come out, goes back together in reverse. Take out plug one and stick your finger in the hole, have someone bump the engine until you feel a push of air, and then put the distributor back in set to cylinder one, put the cap and wires back on, plug back in, and then fire it up and time it.

Oct 27, 2009 | 1986 Ford Mustang

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

Need a engine wiring diagram for a 95 Mustang Cobra 302. Alternator is not charging and the wiring harness was hacked in by previous owner.


try these:
www.allfordmustangs.com/forums/attachments/94.

http://www.veryuseful.com/mustang/tech/engine/images/Mustang-94-95-instrument-cluster.gif

or google: 1995 mustang cobra engine wiring diagram

PLEASE RATE MY ANSWER.

Mar 07, 2009 | 1997 Chevrolet Cavalier

1 Answer

Need to know what size bolts bolt together the bellhousing.


it is a 7/16 ths size bolt about two and a half inches long. i just pulled mine saturday

Feb 26, 2009 | 1983 Ford Mustang Hatchback

1 Answer

Size of valve springs fo 289 ford engine with 302 heads


its not that easy here are some of the things u need to know

* solid or hyd cam
* roller or flat tappet
* valve installed hieght
* rocker ratio
* cam lift

this is just a few things go to a head shop and they will choose the right ones

Dec 19, 2008 | 1965 Ford Mustang

2 Answers

Manual clutch


Sounds like the wrong pressure plate. I got a kit from Autozone and it was the wrong pressure plate. My old one was obviously thicker. With the new pressure plate, the shift fork was almost at full travel before any resistance. That's no good. I had to pull the transmisssion again and use my old pressure plate. Luckily, it was in good condition. Then, the clutch slack was easily adjusted and works great.

Jun 07, 2008 | 1992 Isuzu Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...