Question about 1992 Oldsmobile 88

Open Question

Where is the cam sensor on a 1992 oldsmobile 88 and what is the best way to get to it?? Are there pictures and or a step by step on how to replace??

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: crank sensor

if you are asking about the cam sensor it is easy to replace, passenger side of engine on or near timing chain housing, however, if the cam sensor magnet is weak it too must be replaced, which involves removing the timing gear and chain

Posted on Jul 24, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: I need to find the speed sensor on a 1992 oldsmobile 88

I need to know what size motor to help.

Posted on May 17, 2009

  • 53 Answers

SOURCE: need wiring diagram for 1992

i have the diagrams but they will not load as best i can tell e-mail me and i will send them to you ifixemtorun@aol.com

Posted on May 18, 2009

localwonder
  • 6784 Answers

SOURCE: Delta 88 oldsmobile speedometer going out

HI. If your speedometer needle doesn't move, or if it flutters, your speedometer cable may be bad.

To determine if it is the cable, disconnect the cable casing from the transmission and from the back of the speedometer on the instrument panel. Draw the cable out from inside of the casing. The cable looks like a twisted piece or wire. If the cable is broken or if it is dry or brittle. It probably needs to be replaced. If the cable is intact and the same length as the cable casing, the problem is likely the speedometer head.

I would also advise to check the speedometer gear as well.

The speedometer gear is located on the output shaft. Inspect it for damage.

This gear rarely suffers damage because the gear from the speedometer that meshes with it is usually made of a softer material. Sometimes, the speedometer gear on the main-shaft is replaceable. A clip can hold it in place or it can be a pressed fit. A special puller is available to pull these gears on the car.

Posted on Sep 09, 2009

BuzzFlewhart
  • 655 Answers

SOURCE: 1996 Oldsmobile 88, where is the flasher unit so I can replace

I believe it is under the glove box door between it and the ashtray. You'll have to remove the panel under the dash (no big deal) and it is in a metal clip attached to the dash panel. Good Luck

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does it mean if i have cam censor failure,


THe cam sensor tells the computer what position the camshaft is in .The cam sensor is located on the front of the timing cover midway up the front of the engine. be careful and check that the magnet did not fall out of the cam gear

Jan 27, 2011 | 1992 Oldsmobile 88

1 Answer

1992 olds 88 wont start done put on a new cam & crank sensor & a control module but i have noticed my magnat is missing please help


if its missing, you need to replace the cam gear, unless you can buy a magnet seperately and a clip or way to hold it in the gear. I have not seen one in 10 years, so I cant remember how it was held in.

Sep 07, 2010 | Oldsmobile 88 Cars & Trucks

1 Answer

Were is located the interrupter cam shaft #19020 in 1992 oldsmobile,eighty-eight,v6-3.8l engine


The cam sensor is just under the water pump. The magnet is on the cam gear, To replace it the timing cover has to come off along with the cam gear.

Feb 06, 2010 | 1992 Oldsmobile 88

3 Answers

1992 Oldsmobile 88 Royale.... won't start, but all lights come on


Try turning the key to the on postion-not crank, just to he postion right before cranking. leave it in that postion for 15 min, Do this three and after the third time go ahead an try to start it. Hopefully this will reset your security for you.

Aug 29, 2009 | 1992 Oldsmobile 88

1 Answer

Throttle Problems


Go to an autoparts store like autozone or advance (also check out their websites). Some stores can test the throttle position sensor so that you will know if it is the problem or not. No sense guessing or replacing something that doesn't need replacing. Just because the TPS is only a year old doesn't mean it can't be faulty. Hope this helps and best wishes.

Jul 25, 2009 | 1992 Oldsmobile 88

2 Answers

Crank sensor


The crank sensor is behind the harmonic balancer. Not too hard to replace, the harmonic balancer is supposed to come right off but I needed a big 2-jaw puller to get it off.... accessed through the wheel well.

Jul 11, 2008 | 1992 Oldsmobile 88

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...