Question about Kia Sedona

1 Answer

HI ... THE COMOUTER CHECK FOUND PROBLEM IN THE CATALICTY CONVERTER BANK 2... WITCH PART IS BANK 2?

Posted by on

  • yadayada
    yadayada Aug 23, 2010

    need model and year to provide this info

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

It does not matter if your getting close to a 100000 miles you are going to need to replace all

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the 02 sensor bank 1 sensor 1 located on a 2001 Chevrolet lumina ?


O2 sensor(oxygen sensor) is found in the exhaust AFTER the cat converter for that bank

Feb 06, 2016 | 2001 Chevrolet Lumina

1 Answer

I need to know where is bank one sensore 2 fixed


Bank one sensor two is located on the driver side after the catalytic convertor. And yes that's the o2 sensor.

May 24, 2014 | 2002 GMC Sierra 1500

1 Answer

1997 ford expedition 4.6 engine code p133 02 sensor witch 02 is it


Bank #1 Sensor #1 that is the pass side
front sensor in the converter inlet

Replace both upstream sensors

Leave the rear ones

Jul 26, 2012 | Ford Expedition Cars & Trucks

1 Answer

P0175 code bank 2 witch sensor or both


The sensor after catalytic converter.The Bank 2 Sensor 2 O2 sensor should be located after the catalytic converter for bank 2 which should be the left or front bank of cylinders. In some cases both has to be replaced.But first you replace the bank 2 sensor 2 and see if that is helping.But if the problem is same and same error is seen then replace other sensor too.---------- Thank you.

Jan 25, 2011 | 2004 Kia Sedona

3 Answers

Whats the difference between up and downstream sensor on a chevy s10 1997, what exact sensors do i need for bank 1 and bank 2 sensor1


Well upstream from the Catalatic Converter means towards the engine and that would be the location for Sensor #1 on both sides of the engine. And Downstream would be away from the engine past the Catalatic Converter For Sensor #2 on both sides of the engine. Bank 1 or Bank 2 would indicate which side of the engine the trouble is on. ( Bank #1 is the side of the engine that contains #1 Cylinder. Please remember if you are going to change one 02 Sensor then you should change all of them and be sure to clear all codes after all repairs are finished. that will turn the check engine light off. Good Luck and have a good XMASS.

Dec 18, 2010 | 2002 Chevrolet S-10

2 Answers

Hi, I need to take my 2001 Mazda 626 4cyln for SMOG check in CA. But its check engine light is on, diagnosed as code P0421. Appreciate your help to fix this problem, or just to pass the check. Thank you.


CODE P0421. DEFINITION-CATALYST EFFICIENCY LOW-BANK 1. EXPLANATION-THE OXYGEN SENSORS MONITOR THE CATALYTIC CONVERTERS ABILITY TO STORE OXYGEN. PROBLEM CAUSES- 1. CATALYTIC CONVERTER DEFECTIVE (FAILURE POSSIBLY DUE TO #2,3, OR 4) 2. ENGINE MISFIRE OR RUNNING CONDITION. 3. LARGE VACCUM LEAK 4. ENGINE OIL LEAKAGE INTO EXHAUST-VALVE GUIDE SEALS, PISTON RINGS. THE PCM HAS DETERMINED THAT THE WARM UP CATALYST EFFICIENCY FOR BANK 1 IS BELOW TRESHOLD FOR THE CURRENT ENGINE OPERATING CONDITION. (BANK 1 IDENTIFIES THE LOCATION OF CYLINDER #1, WHILE BANK 2 IDENTIFIES THE CYLINDERS ON THE OPPOSITE BANK).

replace O2 sensors, or your Catalytic Converter.

Oct 06, 2010 | Mazda 626 Cars & Trucks

2 Answers

O2 sencer where are they located


The 02 sensor is located on the exhaust system. It should be a single wire sensor. You will find it between the exhaust manifold and the CAT.

May 21, 2010 | 1991 Ford Ranger Supercab

1 Answer

Meaning of code 151 0n 4m41 engine


P0151 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1)
this could be a fluke code I would earse it and see if it comes back before putting the sensor in there not cheap. Bank 2 means witch side of the engine bank 1 is the side that #1 cylinder is on bank 2 is the other side sensor 1 means upstream above the catalytic converter on the engine side sensor 2 is below the catalytic converter

Mar 24, 2010 | 2000 Mitsubishi Montero Sport

2 Answers

Not passing smog check


bank 1 is pass/side exhaustpipe/converter bank 2 is on the driverside,this car has two converters, so you have 4 oxygen sensors, one before and one after the converter on each side, so bank 1 sensor1 is pass/side before the converter, bank 1 sensor 2 is pass/side after the converter, then bank 2 sensor1 is driverside before the converter, before means starting at motor, then bank 2 sensor 2 is driverside after the converter, heres a diagram to help, i hope this is helpful.a9203dd.jpg33c9cf6.jpg

Feb 06, 2010 | 1995 Lincoln Town Car

2 Answers

Need to replace bank 2 sensor 2 on 2003 toyota highlander , where is it located


Bank 2, sensor 2 is a heated O2 sensor located below (after) the catalytic converter on the passenger-side. When this sensor gets clogged and/or goes bad from rust and heat fatigue, the voltage drops low enough to cause the electronic control module to register error code P0161, which then causes the check engine light to come on.

To replace Bank 2, sensor 2, remove the debri shield from just behind the front bumper, underneath the vehicle. There will be 10 bolts holding it on (10mm, I believe). After removing it, look toward the center of the newly exposed area and you will see 2 finger-like objects projecting out from the engine with wires coming out of each. The one on the left (passenger-side) is bank 2, sensor 2. The one on the right (driver-side) is bank 1, sensor 2.

I got my direct-fit sensor online for $55 from Remart Auto Parts. I know it is tempting to get the universal-fit type and save the cash. But after doing that once, I wouldn't care to do it again.

I found a YouTube video showing pictures of where the two lower (after catalytic converter) sensors are located. While the video only points out the driver-side sensor (bank 1, sensor 2), it's easy to spot the other one being only inches away.

http://www.youtube.com/watch?v=TgQtZci2oOg

If anyone has found this helpful at all, please vote for me.

Dec 01, 2009 | 2003 Toyota Highlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...