Question about 1993 Jeep Grand Cherokee

1 Answer

NEED 2 FIND CRANK SENSOR - 1993 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

On the straight 6 engine it's at 11 o'clock looking from rear, on drivers side of bellhousing. If you have another engine, it is always in line with the flywheel but may be up higher.

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How many crankshaft sensors are there on a Cadillac CTS 2007?


One crank sensor. It needs to go on a scanner. Both sensors are probably OK. Your problem is most likely the timing chains or guides. If ti were the crank sensor, it wouldn't start. Cam sensor would throw a cam code. Correlation means the crank and cam are not in sync. If you have VVT, it could be the actuator.

Sep 30, 2016 | 2007 Cadillac CTS 3.6L

1 Answer

Where is crank shaft sensor location on 95 lexus sc300 please help


images for Where is crankshaft sensor location on 95 ...

eplaced engine on '97 SC300 now new engine does not have Crank ...

www.clublexus.com/.../633233-replaced-engine-on-97-sc300-now-new-...
May 4, 2012 - Location: arizona. Posts: 3 ... apparently 95-97s had an additional crank sensor. .... 1995 Lexus SC300 5spd Na-T ( TT Ecu Mod + a few others) 2jzge position sensor??
Nov 2, 2011
SC400 Crank Shaft Position Sensor. WHERE?????
Oct 11, 2011
SC300 No Spark
Oct 2, 2010
What happens if the Camshaft Position Sensor goes bad?
Jun 18, 2009
More results from www.clublexus.com

Lexus Crank Position Sensor ' LS400 SC300 ES300 GS300 ...

www.partsgeek.com > Crank Position Sensor > Lexus Parts & Accessories
Products 1 - 10 of 68 - 95 1995 Lexus LS400 Crank Position Sensor Denso NLA 7/13 ... 96 1996 Lexus SC300 Crank Position Sensor Denso Includes Pigtail.

Jan 27, 2016 | Lexus Cars & Trucks

2 Answers

Have a 2001 won't start no spark new crank and can and coil pack code keeps saying its no reference signal from crank position sensor


U need to reset your crankshaft position sensor and camm seror also needs to b reset or they need to b replaced

Jan 20, 2016 | Cars & Trucks

1 Answer

Where is crank sensor located on nissan maxima 3.0


crank sensor is at the bottom of the crank pulley. right under neith the pulley is a 2 wire sensor bolted to the engine with 2 bolts.

Sep 18, 2012 | 2000 Nissan Maxima

1 Answer

Have an ECU problem that has caused engine not to fire. Any suggestions?


Check the crank sensor wiring first. If the crank sensor wiring is good and not frayed or broken, replace the crank sensor. The crank sensor tells the fuel injectors and the spark plugs what to do. It's located at the back of the engine on the pass. side about 2 o'clock position and the wiring runs under the engine. There are 2 bolts, some are allen headed and some are bolts that hold it in place. Remove the 2 bolts and the sensor just slides out. It's in between the engine and trans.

Mar 29, 2010 | 2000 Jeep Grand Cherokee

1 Answer

What is the metal plate called that goes on the crankshaft where the timing belt is?


It has many names - 1. Crank Position Sensor Blade, 2. Crank Position Sensor Tone Wheel, 3. Crank Position Blade, 4. Crank Position Tone Wheel, 5. Crank Position Sensor Position Wheel, etc.

Nov 03, 2009 | 1994 Hyundai Sonata

1 Answer

I need to know what size wrenches are needed to replace harmonic balancer and crank sensor on my 1989 buick century 2.8 ltr. engine


you will need sockets,the crank bolt i belive is 22mm and you might need in impact wrench to remove bolt. the crank sensor is 1/2 in or 13mm, that a rachet is good.and to remove balancer sometimes youll need a puller. hope this helps.

Oct 13, 2009 | 1989 Buick LeSabre

1 Answer

Looking for the location of the crank position sensor and the knock sensor for a 2001 chevrolet silverado with a 4.8 8cylinder engine


Crank sensor; right (pass.) side of block above the starter. You may have to remove the starter to remove the crank sensor.

Knock sensor: There may be 2, a front and a rear. Both would be UNDER the intake manifold on top of the engine block one behind the other about 8 inches or so apart. The manifold and associated item may or may not need to be removed to access the sensors.

Aug 10, 2009 | 2001 Chevrolet Silverado

1 Answer

2002 Chevy Silverado, crank sensor installed. can't start truck.


After installing a new crank sensor, a Tech 2 will need to be hooked up in order to complete what is called a relearn procedure on the new crank sensor. Until this is done, your truck's ECM is unable to determine when cylinder #1 is at TDC and electronic timing is unable to be performed. Need to tow to GM dealership for this proceedure.

Jun 17, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Need location of both crank angle sensors


If your Max is 3.5 which it should be unless its 2001, than this Max has 3 sensors. 1 crank and 2 cam. Crank sensor is in the front of the bell housing, behing cooling fan, where engine and trans meet. than other 2 sensors are on sides of the cylinder head in both banks by the air filter box. They are 3 wire connectors and the cam sensors are bare to unplug and replug properly, so good luck. The connectors have these green slides, thast have to be pushed to unlock the connector, however when you going to replu it, you need to make sure, that the green lock/slide piece inside the connector slides back into position, or the sensor could unplug. You need to push the green slide and pull on the connector at the same time to unplug sensor.

Jul 19, 2008 | 2002 Nissan Maxima

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...