Question about 2000 Jeep Grand Cherokee

1 Answer

2000 jeep cherokee sport...can I check the engine codes by cycling ignition switch?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

If so just turn the key to run position ( not start) then one click back. Do this a total of 3 times ending in the run ( or on; not start) position. The odometer will display the code(s) or in an older model the check engine light will flash out the code. Have your pen and paper ready to jot down the results.

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep cherokee sport. the "check gauges" light


check all hose clamps and tighten them up.Do not do this until motor is cooled down and add coolant to level mark on holding tank.

Apr 04, 2011 | 2000 Jeep Grand Cherokee

1 Answer

Will a 2000 4.0 from a jeep cherokee sport replace a 2000 4.0 in a jeep grand cherokee?


Yes...both are identical. Only thing I'd check further on is if one has a manual transmission you may have a different flywheel flange or will need a pilot bushing if the vehicle getting the engine is stick.
If both are automatics...no problem at all.

Feb 20, 2011 | 2000 Jeep Grand Cherokee

1 Answer

2000 cherokee sport / ran good / had plugs changed & new valve cover with new gasket = picked it up , check engine lite on; scaned it ; comes up cycl 6 misfire everytime? [6cyl4.0]


Sounds like something may not have been reinstalled properly. I would take it back and have them recheck the job. I would check around that cylinder to see if something was left disconnected. Also check the spark plug gap of that plug, it may be incorrect.

Oct 24, 2010 | 2000 Jeep Cherokee

1 Answer

1993 jeep Cherokee sport ignition sometimes works


check the connections between the starter, battery and ignition. if all are fine replace the ignition switch

Apr 29, 2010 | 1993 Jeep Cherokee Country

1 Answer

Jeep cherokee sport (year 2000) -- re: bypass for remote ignition


if you went to jeep
they'd tell you not to do that(use what you bought)
Jeep has the right parts....

why to go geeks , its car not a PC.

your car has the IMMO called SKIM. (complex , RTM yet, no)
it will not be hacked by ANY geek or box.
JEEP uses, rolling encrypted codes to start the engine.
SKIM allows it.
your trying to bypass that with out jeeps help is nuts.
over the top, waste of time or even worse DANGEROUS.

why put this junk on your car.?
the car works great with out it.!
then late, you need car fixed and your mechcanic
needs to jump hoops to discover what some other idiott did.
hacking up a good working car.
or far far from town and it fails, and nobody can help
you did that to your self.!!!

here, go to jeep
buy the MOPAR system if H3ll bent to have this junk

Mar 28, 2017 | 2000 Jeep Grand Cherokee

1 Answer

Code u1411 on jeep grand cherokee


Implausible fuel volume is the code,but it most likely was set from a bad ignition switch.It has to do with the malfunction of the switch,really setting a false code,and there might be another one also,but the ignition switch will correct the problem.

Jan 22, 2010 | 2005 Jeep Grand Cherokee

1 Answer

I have a 2000 Jeep Cherokee sport and it just won't turn over. It has full power inside and a brand new battery.


You need to begin testing at the battery using a volt meter. Power requirement of interior is far lower than the starter needs. Check battery for 12v, check that posts & terminals are clean and secure, Check starter relay in the power distribution center, make sure grounds are good at the engine end. Check for 12v at the starter main terminal and 12v at the starter trigger wire with the key in the start position. (if you have both, likely starter has failed,) if power only at main terminal, re-check relay, and also test neutral safety switch and ignition switch.If no power at main terminal go back to the battery and re-test everything between again.

Nov 25, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Cherokee Sport 4.0l


Find out what the code is from the check engine light. Autozone will usually read them for free.

Apr 14, 2009 | 2000 Jeep Cherokee

1 Answer

1998 Jeep Cherokee Sport Ignition Lights Come on but wont crank


Try putting the car in neutral and starting. If its a manual trans it might be the clutch pedal safety switch or it may be something as simple as a loose battery connection.

Feb 03, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...