Question about 2000 Chevrolet Silverado

1 Answer

Engine will idle after starting but will not continue to run after being put in gear

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,130 Answers

Possible that the engine tuning is out of sync. Try to check the fuel intake pressure , adjust the calibration, adjust the timings , set the idling speed.
If the vehicle is stalling on motion then the engine needs more fuel , possible fault in the system to deliver the correct ratio of fuel.
So check this out.

Posted on Aug 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car will start but put it in gear engine will die


engine starts with no problem; but, when I put in gear and ...

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusNov 15, 2012 - The engine just fall dead when you step on the gas; it seems to jerk before ... My car does the same thing but i put it in neutral n it starts up. ... I have a 2004 kia optima it jerks when I go into reverse it was driving ... start and run fine butwhen I put it in drive or any other gear it dies! ... 2002 Hyundai Elantra GT.

Engine stalls when tranny put in Drive or Reverse - Kia Forum

www.kia-forums.com/kia-carnival...2002.../43407-engine-stalls-when-tr...

Feb 28, 2008 - 10 posts - ‎3 authors
Give it a little gas before putting in D or R and it will go. .... When I start the van cold and shift the tranny into drive or reverse.....the whole front ... won't run in forward gears - Kia Forum
10 posts
May 25, 2012
Intriguing problem - engine rough idle & hesitation ...
10 posts
Aug 31, 2011
2006 Kia Spectra engine stalls and bad idle, cleaning the ...
10 posts
Aug 30, 2010
2002 Kia Spectra Won't Go Out of Park - Kia Forum
3 posts
Oct 28, 2008
More results from www.kia-forums.com

Dec 17, 2015 | 2002 Kia Rio

1 Answer

Car dies when in gear


Idle speed sensor is a possibility

Apr 11, 2014 | 2000 Buick Park Avenue

1 Answer

1996 mercedes c280 dies when put in drive


Engine stalls or RPM fluctuates at idle up and down or dies near idle.

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve but always run a OBD2 fault code as well as the cleaning procedure. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Oct 15, 2012 | 1996 Mercedes-Benz C-Class

1 Answer

I am haveing trouble with my 1996 Mazda B2300, When I start my truck after its been sitting for any length of timeI have to rev the engine to get it started, I have to continue reving until engine is warm...


Replace the temperature sending unit/sensor. This sensor tells the computer to put the engine into cold start mode and it then sets idle a bit higher and puts a bit more fuel into the engine to keep it running without having to touch the throttle. Once it's warm, sensor tells computer to go to normal run mode and it's done. No problem.

Dec 19, 2017 | 2005 Dodge Caravan

1 Answer

Starts fine,idles fine,stalls when put in gear to drive away


Try depressing slightly the gas pedal to see if the engine continues to run when you put it in gear. Might have to depredd gas pedal and brake simultaniusly. if the engine continues to run, then the problem is in the idle circuit. Try decarboning the throttle body and the idle speed control.

Mar 26, 2010 | 1989 Honda Accord 4 Door

1 Answer

The idle drops when i put it in gear almost stalling the engine


That is normal, in park or neutral there is no resistance on the engine when you put it in gear there is resistance because the car wants to move. Also when you turn on the ac that turns on the compressor that is run off the belts of the engine so it puts more resistance on the engine. Low idle is not a problem unless the engine dies.

Oct 22, 2009 | 1992 Honda Accord

1 Answer

Engine shakes and hesitate when started until it idles down


Sounds like its missing on 1 or more cylinders. A check of the plugs and wires is in order, Could be a fouled plug or a loose/bad sparkplug wire. Best of luck.
Greg

May 21, 2009 | 2002 Volkswagen Jetta TDI

1 Answer

1997 mercury sable dies when put in gear


Your transmission torque converter lock up clutch is not unlocking, that kills the engine and is the cause of the OD light flashing.

Oct 15, 2017 | 1997 Mercury Sable

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...