Question about 2000 Ford Expedition

1 Answer

Air ride suspension diagram, I need to locate the compressor the system wont hold air

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My compressor for my air ride suspension went out,so i changed it and now i cannot get power to my compressor.

Posted on Feb 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air ride suspention won'twork


If the car is riding lower than usual, making abnormal sounds, and its compressor won't start, it indicates the replacement of air suspension compressor.Accordingly, if the compressor has failed, there is usually an air leak somewhere in the air ride suspension that needs to be found and fixed before a new compressor is installed.

The air compressor is what provides the air suspension system with compressed air required for it to function. If you suspect that there is a problem, you should have proper vehicle suspension inspection by a professional technicians such as Eurobahn BMW MINI Mercedes-Benz Audi. They can determine if the vehicle needs an air suspension compressor replacement or repair.

Aug 09, 2017 | Cars & Trucks

1 Answer

How do i get the on bored compressor to work on my 2003 Hummer H2


There is a lot involved in is air ride suspension system ! A 60a Fuse in the under hood fuse block Marked VSES / ECAS .This is the power for the compressor . There is a air suspension control module , Ride height switch , Fuse in the I / P fuse block 4 WD 15a supply's B+ to ride height switch . There is a electronically controlled air suspension relay that the control module energizes to send power to turn on the compressor.

This system can an will store DTC"S in the control module !
Diagnostic Starting Point - Air Suspension
Begin the system diagnosis with the Diagnostic System Check - Air Suspension . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control module(s) which command the system.


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and their status.

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.
If you don't know about this stuff , I strongly suggest you take it to a repair shop ! Do you know about electrical circuits , relay's fuse's ? Do you know how to use a volt meter, read a wiring diagram. The first thing to do would be hook up a scan tool ,not a code reader. This system can set several DTC'S -diagnostic trouble codes.
DTC B2795 DTC C0563 DTC C0569 DTC C0626 DTC C0631 DTC C0660 DTC C0696 DTC C0702 DTC C0707 DTC C0711 DTC C0712 DTC C0713 DTC C0716 DTC C0717
You need to be able to test for B+ at different points in the wiring !

Mar 15, 2015 | 2003 Hummer H2

2 Answers

1997 mark8 front air ride slamed


Have you checked the height sensor for the front, and the system for leaks ?

Mar 08, 2014 | Cars & Trucks

1 Answer

2003 denali air ride control problem. Compressor was bench tested and runs when 12 volts is applied. Tested pressure switch on air filter (3 wire) and no continutiy between any of the three terminals. I am...


What color wire's ? There is a relay which is controlled by the ESC module (computer ) Electronic suspension control module . The relay supply's B+ power to the compressor . Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model and engine size. Under system click on suspension then under subsystem suspension controls will pop up on it's own . Click the search button then the blue link's . System can set DTC'S - diagnostic trouble code's . Has hight sensors , control module ,relay etc.....

Sep 27, 2017 | 2003 GMC Yukon Denali

3 Answers

The rear suspension air bags no work


start here

The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving condition:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) transfer case inputs, and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines, and the use of an air spring with an air spring solenoid.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed and the vehicle speed exceeds 16 km/h (10 mph).
Air Suspension Switch
The air suspension switch is located behind the RH kick panel on a mounting bracket. The switch interrupts power to the air suspension control module.
The air suspension switch supplies a signal to the air suspension control module. Without the air suspension control module receiving this signal the load leveling system is inoperative and will not react when rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:
  • Is not interchangeable with four wheel air suspension (4WAS) compressor.
  • Consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • Is mounted in the engine compartment between the washer fluid bottle and headlamp (RH front corner).
  • Is a single cylinder electric motor driven unit that provides pressurized air as required.
  • Is powered by a solid state relay, controlled by the air suspension control module.
  • Passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • Air drier has a single port and is not interchangeable with 4WAS compressor air drier.
  • Air drier may be replaced separately.
  • Incorporates a snorkle that may be replaced separately.
The vent solenoid:
  • Allows air to escape from the system during venting actions.
  • Is located in the air compressor cylinder head.
  • Has a 160 psi internal relief valve.
  • Shares a common electrical connector with the air compressor motor.
  • Is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • Has an O-ring seal that prevents air leakage past the valve tip.
  • Opens when the air suspension control module determines lowering is required.
  • Provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • Is replaced with the air compressor as a unit.
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The air springs are mounted between the axle spring seats and the frame upper spring seats.
The two air springs replace the conventional rear coil springs.
Air Suspension Height Sensor
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket). Replace the air suspension height sensor as a unit.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing of the vehicle and related components.
The air suspension control module is mounted in the passenger compartment inside the instrument panel above the radio and temperature controls.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Air Suspension Diagnostic Connector
The air suspension diagnostic connector is used to aid the technician in diagnosing the air suspension system. It is also used to vent the system of compressed air when air suspension system components need to be repaired or replaced. The air suspension diagnostic connector is located under steering column.

Oct 02, 2009 | 1998 Ford Expedition

2 Answers

Where is the location of Lincoln Mark 8 VIII


Air Suspension Compressor Motor/Vent Solenoid : Lower RH front corner of engine compartment C134
Air Suspension Switch : Rear side of trunk C458
Air Suspension/EVO Steering Module : Behind RH cowl panel, above connector bracket C204, C205
Air Suspension/EVO Test Connector : RH side of engine compartment, top of wheel well C117 Soft Ride Relay : Under center front of package tray C403Hard Ride Relay : Under center rear of package tray C404 sorry could not find compressor rely listed, good luck

Aug 06, 2009 | 1993 Lincoln Mark VIII

1 Answer

Mounting locations for air springs compressor and tank


just did google search for ride rite air suspension and found complete install instructions & diagrams....do that!!!

Jun 19, 2009 | 2005 Chevrolet Silverado

2 Answers

Where are the leveling sensors located on a 2003 Navigator?


There is one at each wheel. here is some info

Vehicle Dynamic Suspension The four wheel air suspension system is comprised of the following components:
  • service switch
  • control module
  • two front height sensors
  • one rear height sensor
  • compressor and drier assembly (includes vent solenoid)
  • air lines
  • front and rear air spring and shock absorber assemblies
  • four air spring solenoids
s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The service switch for the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the jack storage area in the rear of the passenger compartment. Failure to do so may result in unexpected inflation or deflation of the air springs which may result in shifting of the vehicle during these operations.
s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not remove an air spring under any circumstances when there is pressure in the air spring. Do not remove any components supporting an air spring without either exhausting the air or providing support for the air spring to prevent vehicle damage or personal injury.
Air Suspension Pneumatic Diagram 17d59a6.gif
Item Part Number Description 1 5319 Air compressor and drier 2 5B322 Air line T-fitting 3 5B321 Air line union 4 — Air line Y-fitting 5 18945/5311 Air spring and solenoid

Suspension Height Sensor Removal and Installation
NOTE: Front shown, rear similar
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the LH quarter trim panel. Failure to do so may result in unexpected inflation or deflation of the air springs which may result in shifting of the vehicle during these operations.
    Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Disconnect the sensor arm. 721ed10.gif
3. Remove the bolts and the sensor. b198e3c.gif
4.
  1. Disconnect the electrical connector.
---------------------------------------------------------------------------------------------

Ride Height Adjustments
Special Tool(s) s3j~us~en~file=st2332a.gif~gen~ref.gif Worldwide Diagnostic System (WDS)
418-F224

New Generation STAR (NGS) Tester
418-F052 or equivalent scan tool
Inflation and Deflation of the Air Suspension System
  1. NOTE: Make sure that the air suspension switch is in the ON position
    NOTE: Make sure that a battery voltage of at least 11 volts is maintained while carrying out this procedure.
    Turn the ignition switch to the ON position.
  1. Connect scan tool to the data link connector (DLC).
  1. Select Air Suspension Control Module under Active Command Mode:
    • VENT FRNT to deflate the front down.
    • LIFT FRNT to inflate the front up.
    • VENT REAR to deflate the rear down.
    • LIFT REAR to inflate the rear up.
Calibration
Ride Height Resetting
  1. NOTE: Make sure that the air suspension switch is in the ON position
    NOTE: Make sure that a battery voltage of at least 11 volts is maintained while carrying out this procedure.
    Turn the ignition to the ON position.
    • Exit the vehicle, close all doors and allow the system to vent the vehicle down to kneel height (approximately 45 seconds).
  1. With the ignition remaining in the ON position, shift the vehicle into DRIVE and then back to PARK.
    • Exit the vehicle, close all doors and allow the vehicle to pump to trim (approximately 45 seconds).
  1. Measure the ride height. For additional information, refer to Section 204-00 .
  1. Open the LF door.
  1. Connect scan tool to the data link connector (DLC).
  1. While outside of the vehicle, select the proper vehicle year, model and engine type.
  1. Select 4WAS module.
  1. Using the active command mode, vent or lift the vehicle to achieve the correct ride height.
  1. Select the "Save Calibration Values (Store Ride Height)" scan tool command to calibrate the 4WAS module.
-------------------------------------------------------------------------------

Jan 09, 2009 | 2003 Lincoln Navigator

11 Answers

No air reaching air bags/compressor does not come on when car turned on


This is a very common problem with all Lincolns. The air ride suspension are marketed as a luxury-comfort item but most do not know that they have a 100% failure rate and are designed to fail as shortly after the warranty expires as possible. The air bags that support the weight of the vehicle are not designed to withstand temperatures below 40 degrees or above 94 degrees and are very prone to dry rot. Once the bags start getting tiny cracks and leaks they start overworking the compressor. (Picture trying to blow up a balloon with holes in it.. you will try for as long as you can but will ultimately have to give up) These air ride systems can be very difficult to accurately diagnose the first time and consequently very expensive. Most people seem to be converting to a passive suspension system these days as the ride quality is too similiar to notice a difference and the reliability is paramount. http://www.strutmasters.com offers a high quality conversion kit that utilizes powder coated American steel coil springs that are actually designed to last the lifetime of the vehicle. http://www.strutmasters.com/lincoln-suspension-parts-s/1.htm there is a direct link to the Lincoln page. I hope this helps save some of you a little bit of grief and a lot of money in the long run!!

Aug 24, 2008 | 2004 Lincoln Town Car

Not finding what you are looking for?
2000 Ford Expedition Logo

962 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...