Question about 2004 Ford Explorer

1 Answer

Should the fan pulley line up with the crankshft pulley

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Yes all pulleys should line up, one belt drivs all pulleys.

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 honda accord changed timing belt and crank case sensors replaced them now car turnes over fires gets gas but wont crank


check to make sure that the crankshft and cam gears were lined up correctly with # 1 cyl at top dead center.

Jul 08, 2012 | 1997 Honda Accord

1 Answer

How do I tighten the vibration dampening pulley on the end of the crankshaft? 3.4 engine Replaced the belt and belt tensioner, still squeals and belt does not run true on tensioner pulley. Vibration...


Using a air impact gun would be quick and simple. Check the pulley, sometimes the rubber seperates from the actual pulley. Crankshft pulleys usually don`t walk off. I think it seperated. Have your service shop take alook..

Feb 19, 2011 | 2001 Chevrolet Impala

1 Answer

Have a rebuilt 6.2 chev diesel. broke alternator belt. got new belt and put it on lower pulley, fan pulley and alternator. it keeps throwing the belt when revving the engine up. tried ac pulley, fan pulley...


It sounds like the alternator is not properly lined up. You had the belt on right the first time. Put it back on and before you start the truck check the alignment on the belt. From the side of the truck look down thw belt to the fan pulley and see if you notice a slight bend, or use a straight edge to do the same thing. Also sight down the belt to the crank for the same thing. Yoiu may have to shim out the alternator brackets to get the belt in line with the other pulleys. Hope this helps.

Oct 17, 2010 | 1988 Chevrolet G30

1 Answer

I have a trouble code p0336 and my blazer wont start


computer is not getting a good signal from the crankshft position sensor and is not able to time the spark properly. Sensor is usually mounted near the crankshaft pulley. Check the connector at the sensor, the mounting of the sensor, and trace the wire for possible short or damage. If looks OK, consider replacing the sensor itself. Questions, let us know.

Sep 09, 2010 | 1998 Chevrolet Blazer

1 Answer

I'm looking for a crankshft pulley. It has 3


dorman aftermaket parts ,just got one bout $90.00

Jul 02, 2010 | 1992 Mitsubishi Mighty Max

2 Answers

Crank shaft pulley on chevy venture not inline with other pulleys ?


hi, if this is the case on your vehicle, you need to get it to a shop to have inspected sooner than later. if this problem is the crankshft pulley out further than the rest of the pulleys, the harmonic balancer is coming apart most likely. if this does occur, it may spin off at very high rpms and tear up whatever gets in it's path insode the engine compartment. could be very costly. side note: i once saw a harmonic balancer come apart on a 9 second drag racing car and it ripped through the passenger seat area and went out the back window, not at all likely to happen to your van, since you're not reving at 7000 plus RPM's, but just an idea.

Jun 07, 2010 | 1998 Chevrolet Venture Cargo

2 Answers

I have a 1999 300m, the harmonic balancer pulley is wobbling, Should I replace, and also will that cause a metal sound??


Most definitley replaceas it evens out crankshft vibrations. May cause metallic sound replace ASAP.

Mar 10, 2010 | 1999 Chrysler 300M

2 Answers

Where is the crankshaft sensor located


your ignition system doesn't use a Crank sensor, it uses a distributor Hall Effect magnetic pickup, both parts do the same thing but in very different ways, the hall effect is located inside the Distributor. here is the part number.
STANDARD MOTOR PRODUCTS Part # LX359 Price $51.79 Source: www.rockauto.com

Jun 29, 2009 | 1994 Cadillac DeVille

1 Answer

How to time a dohc 3.4 1995 monte had broken belt thanks


HI...
TO set timing belt. on a 3.4 95 chevy.
you need to remove the VALVE Covers.
at the and of the camshafts, you will see grove.
In the grove you need to put a metal flat piece croosing both of the cams. to lock on position.
and put the timing mark on the crankshft pulley ore sproket.

OK.. I hope this help on your question.
Thank you for use fixya.

Jul 30, 2008 | Chevrolet Monte Carlo Cars & Trucks

Not finding what you are looking for?
2004 Ford Explorer Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...