Question about 2006 Lexus Gx 470

Open Question

Do I need to remove the battery to replace the left front turn signal bulb or is there an easier way?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 79 Answers

SOURCE: Need to replace left front turn signal bulb

yes

Posted on Mar 22, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My left turn signal was flashing fast. I checked bulb in back left. Turn signal good but bulb below it was out. I changed that one but turn signal still flashing fast. all other bulbs look good. ??


If the front and rear bulbs flash fast also, replace the hazard switch or you could live with it. As they are working. If one doesn't work, check grounds. I just run a new ground, much easier than cutting open the harness to find the break.

May 31, 2015 | 2012 Nissan Rogue

1 Answer

My left flasher stopped working suddently


If the right flasher is working and the left flasher is not, that should be a burned out light bulb, either front or rear. (outside)
If you will wait until it is dark, it is easier to diagnose.
After dark, turn on the right turn signal, then look carefully at the brightness of the front and the brightness of the rear turn signal. Now, turn on the left, and again observe the brightness of each. One of the bulbs should be out, or not as bright as the other side. That is the bulb you will need to replace.

Jan 14, 2013 | 1997 Buick Park Avenue

1 Answer

How to change turn sign light


Instructions
1Start your vehicle's engine. Turn the steering wheel the opposite direction of the bulb you need to change. If you need to change the left turn signal light bulb then you will turn the wheel as far as you can to the right. This moves the wheel out of the way so that you have access to the fender and the turn signal assembly.


2Get down by the front fender of your vehicle. Use a Philips screwdriver to remove the screws from the wheel well cover. Take off the wheel well cover and set it off to the side.




3Stick your hand into the wheel well and find the turn signal bulb. Turn it to the left and unscrew it from the turn signal assembly. Remove the bulb.


4Take your new turn signal light bulb and screw it into place using your hand. Replace the wheel well cover and use the Philips screwdriver to secure it in place. Repeat this process for the turn signal on the other side of the vehicle.

Read more: Chinasinoy

Aug 03, 2012 | 2010 Kia Optima

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

1 Answer

How to replace the left front turn signal bulb?


Open the hood and take out the four bolts that hold the headlight in position. They are all on the top and include one rather long bolt that will still remain attached even after loosened. Once you have done this you can move the headlight unit to the side (or you can disconnect it and remove it altogether). Removing the headlight unit will make it possible to reach the turn signal assembly which you can then twist to remove from its seating. You can then replace the bulb and then replace the headlight unit.



  • FRONT Turn-signal - 3457 AK (amber) this is the number of what bulb you need

Dec 06, 2010 | 2000 Ford Taurus

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

1 Answer

Cant figure out how to replace front blinker bulb


You need to remove the front grill to get at the front turn signals (and bulbs). A lot of work for what should be much easier.

hope it works

Jan 09, 2010 | 2006 Hummer H3

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...