Question about 2004 Hyundai Elantra

1 Answer

How do you adjust high beams on 2005 Hyundai Elantra? I got the low beam adjusted ... Don't see the high beam adjustment

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

There is no adjustment for high beams, they follow suit with the low beams.

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust the dipped lights on a hyundai teracan


the bulbs are set in the reflector to get maximum illumination and cannot be adjusted. What you have to adjust is high beam and the low beam will be automatically adjusted. Th adjust high beam (after dark) place the vehicle on level ground about 3 feet from a wall. Turn on high beam and you will notice where the centre of the beam is on the wall That centre has to be slightly below the centre of the lights ( about 1 inch) The centre should be directly in front of the lights and not out to the side of the vehicle. When the lights are correctly adjusted then low beam will be in the correct position.

Nov 23, 2014 | Hyundai Cars & Trucks

1 Answer

My high beams will not adjust up and down on the drivers side on my 2005 hyundai elantra


if the adjusters are sticking spray them with wd40 or give them a wiggle after loosening the screws....poss just rusty...

Jul 29, 2010 | 2001 Hyundai Elantra

1 Answer

Can't find headlight adjustment screws


They nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.


Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Sep 17, 2009 | 2005 Hyundai Elantra

2 Answers

My low beam lights sometimes stop working i still have high beam and daylight runing lights after a while they come on.2009 elantra dealer can't find problem.


when the low beams quit try switching from high to low and back and see if low beams stay on, if they do it may be the dimmer switch, if that doesn't change anything suspect the headlight switch.

Sep 02, 2009 | 2009 Hyundai Elantra

2 Answers

How do you adjust the headlights in a 2005 Chevy Colorado?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 15, 2009 | 2005 Chevrolet Colorado

1 Answer

Replacing headlights and adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 02, 2009 | 2005 Chevrolet Monte Carlo

1 Answer

Adjusting the low beam headlight on a 2003 Hyundai Elantra


thats it my freind one on each side/Plaes rate my response thank you very much

Jan 30, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Adjusting the low beam headlight on a 2003 Hyundai Elantra Adjusting the High beam headlight on a 2003 Hyundai Elantra


its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Jan 30, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Adjustment headlights '02 Hyundai Elantra


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 23, 2009 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
2004 Hyundai Elantra Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...