Question about 2000 Chevrolet Malibu

Open Question

How to remove a door panel off a 2000 chevy malibu

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: How to remove rear door panel on 2003 Chevrolet Malibu?

not sure

Posted on Aug 13, 2008

Ad
rick_amick
  • 69 Answers

SOURCE: drivers door panel removal

The book says 1. remove power accesory switch panel by using suitable flat blade tool at front. 2. Disconnet electrical connections.
3. pry door handle plug by using small flat bladed tool
4.remove door trim handle mounting screws
5. remove door trim panel from retainers.Start at rear bottom corner and pry outward.
6. remove door panel.
KD does make a tool that will properly pry the door panel away from reainers. KD 3705 You might get by with a screwdriver.
One other thing you may need to have the window down to get the panel to come off. You will have to lift up on it once it is loose from the fastners.
Hope this helps you out.

Posted on Mar 24, 2009

  • 1986 Answers

SOURCE: how remove rear door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: Replacing Motor and Regulator on 2000 chevy silverado

you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to pull off the seal in order to see inside the door. The motor and regulator will be held in by a few bolts that may be tricky to get to.... This is probably going to be up to 3 hours if you're unsure of what to do...

Posted on Aug 19, 2009

  • 4 Answers

SOURCE: fuse panel location and diagram 2000 chevy malibu

if the car is built like monte carlo for 2000 there are 2 fuse panels inside. one on the driver side when you open door and theres one the passenger side when you open the door there are panels on both sides of the dash that pull off. and then of course there are the fuse blocks under the hood. by the battery.

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to change blow motor resistor in a 2000 chevy malibu. How do I get to it?


remove panel from beneath glove box, you will see ecm just slide it to the side. now you should be able to see the fan. resistor is beside it!! remove connection then remove resistor. ( it may save on your back just to remove glove box. about 8 screws! ) have a good day !!

Oct 30, 2010 | 2000 Chevrolet Malibu

1 Answer

2007 malibu max rear door panel removal


how do i get the rear driver door panel off without distroying it???
2007 chevy malibu maxx 6cyl.
Stb723@gmail

Mar 23, 2010 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

1 Answer

Hi there ..I just got a driver side window motor,to replace my old one in my 99 Chevy Malibu..whats the steps to take to take off the old one and place the new ??


GM Malibu/Cutlass 1997-2000 - Repair Guide

Window Regulator And Motor Assembly
REMOVAL & INSTALLATION

Rear Door


4f4e997.gif
Fig. The rear window regulator is an assembly that consists of two pieces

NOTE The front window regulator is removed as an assembly with the door control module. Refer to the procedure outlined in this section under Door Locks.
  1. Remove the door panel and the water deflector.
  2. Remove the door glass (window).
  3. Detach the electrical connector, if equipped, or remove the window regulator handle.

To install:
  1. Install the window regulator.
  2. Place the regulator through the rear access hole into the door.
  3. Attach the electrical connector, if equipped, or install the window regulator handle.
  4. Install the rear side door window.
  5. Replace the door window assembly.
  6. Install the water deflector and the door panel.

Door Locks
REMOVAL & INSTALLATION

Door Control Module


882bea7.gif
Fig. The door control module contains the door locking system module and the power window system module
  1. Raise the window to the full up position.
  2. Remove the inside door trim panel. Refer to procedure outlined in this section.
  3. Pull off the plastic film water deflector enough to access the lock actuator.
  4. Remove the screws securing the door lock actuator.
  5. Remove the door locking system module nuts and bolt.
  6. Remove the door locking system module from the door.
To install:
Installation is the reverse of removal, but make sure to tighten the fasteners to the torque specifications listed:
  1. Door locking system module bolt-89 inch lbs. (10 Nm).
  2. Door locking system module nuts-89 inch lbs. (10 Nm).
  3. Door lock actuator screws-53 inch lbs. (6 Nm).

Hope helps (remember rated this) Good luck.

Jan 21, 2010 | 1999 Chevrolet Malibu

4 Answers

Fuse panel location and diagram 2000 chevy malibu


if the car is built like monte carlo for 2000 there are 2 fuse panels inside. one on the driver side when you open door and theres one the passenger side when you open the door there are panels on both sides of the dash that pull off. and then of course there are the fuse blocks under the hood. by the battery.

Sep 13, 2009 | 2000 Chevrolet Malibu

1 Answer

Passenger front window motor


remove the door panel. you probably need to remove the door handle and window controls first... look for screws and take them out. careful not to lose them. the door panel should be connected by snaps around the whole perimeter of the door, just pop these one at a time until the panel comes off. you should see the window motor and everything should be pretty obvious from there.

Apr 15, 2009 | 1997 Chevrolet Malibu

2 Answers

Drivers door panel removal


The book says 1. remove power accesory switch panel by using suitable flat blade tool at front. 2. Disconnet electrical connections.
3. pry door handle plug by using small flat bladed tool
4.remove door trim handle mounting screws
5. remove door trim panel from retainers.Start at rear bottom corner and pry outward.
6. remove door panel.
KD does make a tool that will properly pry the door panel away from reainers. KD 3705 You might get by with a screwdriver.
One other thing you may need to have the window down to get the panel to come off. You will have to lift up on it once it is loose from the fastners.
Hope this helps you out.

Mar 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Rear passenger window just slides how do I get the door panel off


Well first take the mirror cover off. Then the roll up window handle if its manual. There is a star head behind the handle to open the door, remove that and unplug all wiring.Then behind the handle to close the door there is a cover, it has 2 screws, take those out and the rest is just plastic door clips just pull away from the door and they will start coming off.

Mar 12, 2009 | 2000 Chevrolet Malibu

1 Answer

How remove rear door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Feb 20, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
2000 Chevrolet Malibu Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...