Question about 1985 Nissan Pickup

1 Answer

What engages the fourwheel drive - 1985 Nissan Pickup

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

If the front axles are not free when transfer is in 4x4 check the lockouts (front hubs)

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fourwheel drive dont seem to engage on my 1997 jimmy


the four wheel drive is controlled by a electric actuator that is located on the transfere case

Dec 10, 2012 | 1998 GMC Jimmy

1 Answer

Switch for the 4x4 will not actuate the fourwheel drive.


IS IT THE 4X4 SHIFT ON THE FLOOR YOU PUSH THE BUTTON IN ON TOP OF THE SHIFTER AND ENGAGE YOUR 4 WHEEL DRIVE I NEED TO KNOW SO I CAN HELP HERE AND IT LIGHTS UP THE AX;E YOU HAVE ENGAGE POHLCAT

Mar 05, 2011 | GMC Envoy Cars & Trucks

1 Answer

Fourwheel drive works but when i take out of fourwheel drive i have a howling noise in front end but when i put it back in fourwheel drive it goes away


There is a TSB for replacing the IWE ( Integrated Wheel Ends ) solenoid, as the 1st design can ingest water and introduce it to the IWEs, causing low vacuum, and the gears for the IWE are grinding.

http://my.voyager.net/~sscully/file_tsb06_08_15.pdf

To cure this until you get the new IWE solenoid ordered and installed, pull the vacuum lines from the IWEs and plug them. This will leave the IWE gears engaged, so they are not trying round off the teeth.

There are 2 lines to the IWE, 1 is the vacuum line, the other is a vent line, that routes into the engine compartment, with an open end, make sure you pull and plug the correct line.

This will have the front hubs engaged to a dead axle, so it will decrease mpg, and you will feel a bit of loss of power, but better than ruining a set of IWEs that will cost ~500.00 to replace.

Jan 09, 2010 | 2005 Ford F-150

1 Answer

Four wheel drive computer clicks when i try to engage 4x4


tap on the 4wd motor on the transfer case while someone is pushing the button, if engages you need a new motor

Jun 30, 2009 | 1987 Ford Ranger

1 Answer

I engage the four wheel drive in my 2005 Ford F-150 when we had a snow storm this week.Now when switching out of fourwheel drive the transmission wines until you switch it back to fourwheel drive...


the four wheel drive uses vacuum hub locks. there is a vacuum solenoid on the passenger firewall in front of the battery box. sounds like you need a updated solenoid and possibly one or both hub locks. what happens is the old style solenoid vent allows water to get in and the hub locks freeze or stop working because of the water. the new style has a cover over the vent to prevent water from getting in.

Mar 05, 2009 | 2005 Ford F-150

1 Answer

Fourwheel drive components


if it is a 4x4 the switches are on the dash board in frot of you, in order
2 HI , 4 HI ,4 LO

Dec 27, 2008 | 2004 Chevrolet TrailBlazer

1 Answer

Front end pops in and out of fourwheel drive


check for leaks in the vacuum, Jeep used a vacuum switch for the front axle during that time on the dana 30, it may have a leak or just worn where its not fully engaging and lockign all the way. It may not be holding the air as well to keep it engaged. Its a small tube.

Dec 14, 2008 | 1992 Jeep Wrangler

1 Answer

When i push the button to put it in fourwheel drive. the hubs do not engage.


to engage gear shift must be in netural with hand brake on this solved the problem for me
cheers max

Nov 29, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...