Question about 1992 Audi 100

1 Answer

The power window run my battery down. They will close with the key off on their own. what is the problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Had the same issue. for me it was the central locking control unit located next to the battery

Posted on Feb 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't find the fuse for the power windows on a 1998 Lincoln Navigator


All the other windows work ? Not a fuse , one fuse powers all the windows . Test for B+ voltage at the switch an the window regulator would be the proper diagnostic procedure . Do you own a volt meter ? know how to read a wiring diagram ? how to do basic automotive electrical testing . The Faint click you hear is probably a relay , which means the GEM - genaric electronic modual is energizing the window relay . The windows are computer controlled .

The GEM will activate the OTD Relay until one of the following conditions is met:
  • The LF regulator control switch is pushed to the UP position.
  • The LF regulator control switch is released (OFF position) and then moved to the down position (first detent) or one touch down (OTD) position (second detent).
  • Seven seconds have elapsed since the OTD was initiated.
  • A window regulator electric drive stall condition is detected on the one touch down sense line inputs.
The UP window operation is not controlled by the GEM. The feature is activated when the delayed accessory is active and the LF window regulator control switch is pressed to the UP position. The switch provides delayed accessory power to one side of the motor and ground to the other side through the one touch down relay. The one touch down relay is not active when the LF regulator control switch is in the UP position.
Passenger windows may be raised or lowered using the LF master control switches or the appropriate passenger window switch. Passenger window switches receive power when the delayed accessory relay is active and the LF remote lock-out switch is in the UNLOCK position. When in the LOCK-OUT position, the passenger windows are deactivated.
The GEM controls manual down and auto down window movement with the down window relay. The relay is activated by applying ground directly to one side of the down window relay coil, and deactivated by removing the ground signal.
The delayed accessory relay provides power for the operation of the power windows and the power moon roof. The delayed accessory feature is active when the ignition switch is in the RUN or the ACC position, or when the ignition switch is changed from RUN or ACC to the OFF/LOCK position and the LF and RF doors are closed.
The GEM will deactivate the delayed accessory feature when:
  • the LF door is ajar and the ignition switch is in the OFF/LOCK or KEY-OUT position.
  • the RF door is ajar and the ignition switch is in the OFF/LOCK or KEY-OUT position.
  • 10 minutes have elapsed since the ignition switch was changed from ACC or RUN to the OFF/LOCK position.
Feature inputs:
  • LF door open warning switch (open circuit with door closed, grounded with door ajar).
  • RF door open warning switch (open circuit with door closed, grounded with door ajar).
  • Ignition switch RUN position (battery potential on both the RUN and RUN/ACC inputs).
  • Ignition switch ACC position (battery potential on the RUN/ACC input).
  • Ignition switch OFF/LOCK position (absence of battery potential on the RUN, RUN/ACC, and START inputs).
The Trainer 24 Power Window Troubleshooting

Mar 03, 2017 | 1998 Lincoln Navigator

1 Answer

How to reset windows on is 350 lexus 2007


(a) Turn the engine switch on (IG).

(b) Halfway open the power window by pressing the power window switch.

(c) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 1 second after the power window is fully closed.

(d) Check that the AUTO UP/DOWN function operates normally.

If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time. If not normal, follow the steps below.

(1) Disconnect the negative battery terminal for 10 seconds.

(2) Connect the battery terminal.

(3) Turn the engine switch on (IG).

(4) Halfway open the power window by pressing the power window switch.

(5) If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time.

If not normal, follow the steps below.

(6) Turn the engine switch on (IG).

(7) Halfway open the power window by pressing the power window switch.

(8) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 12 seconds after the power window is fully closed.

(9) Check that the AUTO UP/DOWN function operates normally.

Feb 05, 2017 | 2007 Lexus IS 350

3 Answers

I disconnected battery cables on small suv to clean them. After reattaching, I noticed rear window on tailgate went down about 8 inches. I then raised window by button on dash. It closed for a moment and...


its lost its memory ,hold key in lock and close window then holding key in closed position for 10 secs should reset the memory in the electronic control box on the window motor memory inside this control box

Dec 19, 2011 | 2002 Land Rover Freelander

1 Answer

My car wouldn't start this morning, I've got it jump started but the windows which were all open now won't close?


hi sarah,i assume your battery is dead,hence the jump start,if,after charging/replacing the battery,your car windows still wont close reset by using the key in the door lock,(lock car and hold the key over,windows will go up.wait 30 secs then unlock/hold key over,windows will go down,then lock the car again/hold key over until all windows shut then wait 30 secs get in and start the car,you have just reset the system).
geoff.

Jan 25, 2011 | 1998 Volkswagen Golf

1 Answer

Used the key to unlock door and alarm started going off. put key in ignition to start, but wouldn't. removed battery cable, do to neighbors, and the alarm keeps sounding. how can I shut it off? just...


With the drivers window down, and the doors closed. and locked connect the battery and lock and unlock the tailgate with the key, you need to unlock it twice to unlock the doors and turn off the alarm. If the locks are working like thier supposed to the drivers door will be unlocked and opening it won't set off the alarm. the truck should be back to normal. If not disconnect the battery again. Drivers window down. Put the key in the switch and turn the key on to the run position. With all the doors closed connect the battery. connect it good and don't bounce it around. If the battery casbles aren't clean clean them good so it'll connect good. If it still is alarming then the doors switches are likly. Or the door locking motors. You should be able to lock all the doors ( including the hatch) by hand and get the system to reset. Try it all again using a different door to double unlock as a lock switch might be sticking. If the system can't verify that all the doors are closed and locked it won't reset. If you connect the battery wihg the key turned on the system thinks it's already running and appeares to be in the unset mode.

Dec 16, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Security system went off after replacing battery now car wont start nor fuel pump will turn on.how do i fix


You might just need to reset it. Roll the drivers window down and close all the doors. Lock all the doors with the key ) turn the key to lock twice, The electric locks should lock all the doors. wail a few minutes and unlock and open the trunk with the key. relock the truck or just close it. unlock the drivers door with the key, twice. all the doors should unlock, get in and start the car. Now this does'nt always work. If it does'nt we'll make the system think it's running. Close and lock all the doors. open the hood and disconnect the battery, one ccable will be fine. wait a few minutes. Reach in though the open window and turn the key all the way on. Don't open the doors, go around and connect the battery hard so it does'nt jump or skip. Reach thought the window and start the car/ once it's running. turn it off remove the key and unlock the door from the inside and open the door ( as if you were inside.) get in and start the car and everything should be back to normal.

Nov 26, 2010 | 1997 Infiniti.5 J30

2 Answers

1997 jetta will not start. the battery has been disconnected and charged. Is it true that when the power has been disconnected that there are some security steps to go through before the car can be...


all vw MUST be reset after battery dies/changed.put key in door,unlock/hold key over 30 secs(windows go down)then lock/hold key over 30 secs(windows go up/sunroof closes)then press unlock button on remote for 30 secs......RESET DONE......(try this for fun....sit in car after turning off engine/remove key,drivers door keypad is still live(until you open door)ALSO when engine is running lower any window and then raise up with fingers in top of door,the window will rollback.(if you do it once it hurts..twice it really hurts..three times it traps your hand in.)ALL THIS is NOT in the handbook.......

Nov 06, 2010 | 1997 Volkswagen Jetta

2 Answers

None of my power windows on 1998 Mercury Mountaineer work, checked fuses but can't find power relay if there is one. Any suggestions


If you checked the fuses and they are fine, try this. With the key on and the window button down or up, open and close the door holding in the up or down position. If the window moves, there is a wire(s) are broken in the wire harness that goes from the door jam to the door. This is a common problem that we find with window and door operating problems. You may find 1 bad or broken wire, or 4-5 broken wires. Let us know if this help you find a repair, for this concern. Craig

Jan 23, 2010 | 1998 Mercury Mountaineer

1 Answer

Back window doesnt roll down properly when you open the door, so I have to push it down a little before I close it. Also the lock bottom for the windows doesnt work.


dis-connect your battery for 30 seconds to do a switch reset on your window, when you reconnect the batt your window will go down, open and close rear door to check lock functions ok first. close rear door and using key or switch inside car close window fully with out stopping, this should reset the window.

Jan 05, 2010 | 2003 Land Rover Freelander

3 Answers

Saab 93 window not closing fully


1. put key to ON, hold window button down until all the way down, then do same for up, repeat one more time until you hear BEEP. You just calibrated your window. You will need to do this everytime you disconnect your battery.
or...
2. anytime window has power and has automatically gone down, hold the X (window lock button) down while holding up on your window button, again untill you hear BEEP. not sure what this does, but it fixed the problem for me.

Feb 08, 2009 | 2004 Saab 9-3

Not finding what you are looking for?
1992 Audi 100 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...