Question about 2002 Mazda Millenia

1 Answer

Thermastat replace - 2002 Mazda Millenia

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 61 Answers

First of all, mark the electrical connectors around the thermostat with numbers. If I remember, there were six of them. After marking, disconnect them. Remove air intake boot from injector. The thermostat is at the end of the metal tube that has a couple of rubber hoses clamped to it. Un-clamp the small hoses. I found it easier using a 1/4" ratchet and 10mm socket to loosen the right bolt on the thermostat housing. To get the left bolt, a 10mm long handle box wrench works best. Do not try to bend the small tube that is welded to the larger tube. You might end up with problems you don't need. When you get a new thermostat, also get a new rubber gasket. There is no service sheet gasket for this type of set up. The gasket for the thermostat is round and has a groove on the inside so it fits around the perimeter of the thermostat and then is placed inside a rabbit fit of the housing. When you tightened up the two 10mm bolts, that will seal it. Hope this helps!

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code 1281


IT MEANS THE ENGINE IS COLD FOR TO LONG SO ITS A TEMPERATURE SENSOR. YOU NEED TO CHANGE THE THERMASTAT IN YOUR CAR. THE GAGE IS WORKING OR YOU WOULD NOT GET A 1287 CODE SO DONT MESS WITH THE GAUGE, JUST GET A NEW THERMASTAT. AND UNHOOK YOUR NEGATIVE CABLE ON THE BATTERY BEFOR YOU REPLACE THIS AND TURN IGNITION TO START POSITION AND DO A TEN SECOND COUT, THEN REPLACE THE THERMASTAT , THEN HOOK YOUR NEGATIVE CABLE BACK UP THIS CLEARS THE CODES IN YOUR CAR SO IT WILL READ NEW CODES AS THINGS GO OUT. ALWAYS CLEAR YOUR CODES BEFOR DOING THE REPAIR AND DONT HOOK UP THE BATTERY UNTIL YOUR DONE WORKING ON IT,

Jul 08, 2014 | 2002 Dodge Ram 3500 Truck

1 Answer

Where is the thermastat located


It's located on the back of the engine, behind the distributor, at the end of the radiator hose.

Aug 03, 2012 | 1993 Honda Accord

1 Answer

I need to find the thermostat location in a mazda '96 B2300 SE


THE THERMASTAT WILL BE LOCATED AT THE ENGINE SIDE OF THE RADIATOR HOSE! ON THE ENGINE, YOU WILL SEE TWO BOLTS HOLDING THE INLET ON THE ENGINE! DRAIN THE RADIATOR, AND REMOVE THE HOSE FROM THE ENGINE INLET! UNBOLT THE INLET, AND YOU WILL SEE THE THERMASTAT, REPLACE IT IN THE SAME WAY THE OLD ONE COMES OUT, (USUALLY THE SPRING SIDE WILL GO IN TOWARD ENGINE)! THEN PLACE THE NEW GASKET ON THE INLET, AND REBOLT IT TO THE ENGINE! REPLACE THE HOSE, TIGHTEN IT DOWN, ADD ANTIFREEZE TILL FULL, START ENGINE, AND CHECK FOR LEAKS! YOU CAN REMOVE THE RADIATOR CAP AND WATCH THE COOLANT, AS THE THERMASTAT OPENS, THE COOLANT WILL START MOVING! REPLACE THE CAP,

Mar 11, 2011 | 2007 Mazda B2300

1 Answer

Thermostat is acting up is it easy to change


YES! DRAIN THE RADIATOR! THE THERMASTAT IS AT THE ENGINE SIDE OF THE TOP RADIATOR HOSE! REMOVE THE HOSE! AND THE THERMASTAT HOUSING HAS TWO BOLTS HOLDING IT ON! REMOVE THE TWO BOLTS, AND THE HOUSING! CLEAN THE AREA AROUND THE BASE OF THE HOUSING! SCRAP OFF THE OLD GASKET FROM THE HOUSING, AND ON THE ENGINE! REPLACE THE GASKET WITH A NEW ONE! PLACE THE NEW THERMASTAT IN THE SAME DIRECTION AS THE OLD ONE COMES OUT! REPLACE THE HOUSING, TIGHTEN THE BOLTS, AND PUT THE RADIATOR HOSE BACK ON, RETIGHTEN IT, AND FILL WITH ANTIFREEZE, AND CHECK FOR LEAKS!

Feb 26, 2011 | 1996 Pontiac Grand Am

1 Answer

Replace thermastat


you will need to remove the exhaust manifold in order to get to the water pump that sits on the thermastat. Once you get the manifold off you will see the water pump there will be 4 bolts that hold the belly to the pump remove them and left it up the thermastat is under it.

Nov 30, 2010 | 1998 Pontiac Grand Am

2 Answers

Where is the thermostate located on a 1998 cadillac catera 3.0 v6 engine


Hi Friend:

To Locate your thermastat, Open your Hood and look down at the top of your radiator.You'll see a Top Raditor Hose that goes from your radiator to your Thermastat Housing.

You'll see a Hose clamp on the Thermastat housing .

NOTE: before you loosen the Hose Clamp Make sure you your car is cooled down and remove your radiator cap to release any pressure that is in your system.

After the Hose is off you'll see a Domed shaped Housing that is your Thermastat Housing. Remove the Bolts that Hold the Housing on and Seals the Cooling System.From Leaking out of the Housing.

After removing the Housing you'll see your Thermastat .Just remove it and Clean up all old gasket Material so you can replace the gasket with your new one .But put in your new thermastat 1st.

Then make sure you seal the gasket with Gasket Glue. And Replace the Housing Bolts and Tighten up good and Sung.

Put back on your hose then clamp.And Refill your Radiator with Coolant.

This will get your new thermastat in and get you Ready to go .

Thanks for using FixYa Please let me Know how my Solution helped you.By Voting .

Thanks Again From: d_hubbs

Aug 22, 2010 | 1998 Cadillac Catera

1 Answer

Thermastat replacement


chilton and haynes make a great bible for your car
you can buy then at chapters indago

Jan 03, 2010 | 1999 Chrysler 300M

1 Answer

1995 toyota 4runner gets hot with new thermastat gasket


the thermostat should be closed when you take it out, therefore the thermostat is bad. It does not closed.

May 22, 2009 | 1995 Toyota 4Runner

1 Answer

1997 jeep TJ, thermostat


about 10-20bucks ez fix buy a new thermastat replace it, if that doesnt work ,then get a coolant flush....if you need help locating the thermastat.. go to ask.com and ask where is the thermastat on """"""""""""///(your veh)

May 18, 2009 | 1997 Jeep Tj

Not finding what you are looking for?
2002 Mazda Millenia Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...