Question about 1999 Ford Windstar

1 Answer

When driving at 60mph this 99 windstar quite moving. No forward or reverse. Is this the neutral safety or a sensor?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

Assuming the engine runs, this sounds like a transmission problem. Check your transmission fluid to make sure it is at the proper level and doesn't have a burned smell. If all is well, you will probably need to have an experienced transmission mechanic look at it for you. Good luck!

Posted on Aug 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have all gears but reverse and when in park and neutral and gas pedal is pressed the car moves forward, why?


well could be two things. either your transmission has crapped out on you. or you have a shifter linkage issue. which means when the car is in park its not really in park. try this. move the shifter and see if the car moves in a different gear then what it says it is in . so if it moves in neutral it could be drive and reverse is neutral. if it does not reverse at all. time for a new trany is my guess.

Mar 17, 2015 | 1997 Toyota Camry

1 Answer

Neutral safety switch


Maybe the Shift interlock cable is your problem from shifting from drive to park but not sure about the reverse.

Mar 18, 2014 | Mazda Millenia Cars & Trucks

1 Answer

99 camry wont shift Code P0500 speed sensor


The problem is a gear internal failure the gear who drive the speed sensor is defect the is why you don't have speed sensor reading. There is a way you can verify that remove the speed sensor drive it with a drill check the dashboard you will see.

Oct 05, 2013 | Cars & Trucks

1 Answer

2000 ford windstar transmisson will not move forward


You have a failed forward clutch, time for a rebuilt.

Jan 06, 2013 | 1999 Ford Windstar

2 Answers

I have a code po705 my car goes reverse neutral


p0705 is the transmission range sensor which tells the ECM what gear the transmission is in neutral/reverse. Which was probably happened when you lost Drive gear

Jun 02, 2010 | 1999 Ford Windstar

2 Answers

Looking for the neutral safety switch


Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Sep 17, 2009 | Ford E-250 Cars & Trucks

2 Answers

1991 Caprice No reverse. Moves in neutral. All forward gears OK.


shift linkage needs adjusting,,could be bent, easy fix, located along firewall to fram beneath the column, ask your son wut he ran over and didnt tell u about... hope i could help...:)

Mar 22, 2009 | 1991 Chevrolet Caprice

1 Answer

Changed tranny in 99 plymouth breeze


probably the neutral safety switch ,and reverse light switch ,

Dec 08, 2008 | 1999 Plymouth Breeze

Not finding what you are looking for?
1999 Ford Windstar Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...