How to timing the mazdaspeed6 ,diagram - MAZDASPEED6 Mazda Cars & Trucks

Engine Temperature Issue - Please Help! - Mazda 6 Forums : Mazda 6 ...

forum.mazda6club.com > ... > Mazdaspeed6

Sep 12, 2011 - Join Date: Mar 2006 ... to the gauge) and then after being shut off for 5 minutes, show COLD. ... I'll also confirm, with my AP, that my ECT is around 200 like it normally is. .... VSS, and ECT signals and calculate radiator's heat the radiation ... I noticed my engine temp needle was dipping down and then came ... CEL - Throwing code P0126 (Insufficient Coolant Temperature ...
Nov 18, 2013
Temp gauge needle
Mar 14, 2013
overheating problems
Jun 5, 2010
Temperature Gauge
May 22, 2010
More results from forum.mazda6club.com

Temperature gauge going up and down - CarGurus

www.cargurus.com > Questions > Infiniti > I30

CarGurusAug 20, 2014 - Also as my temperature gage rises but car does not overheat. ... tempneedle gets up towards the red mark while you're driving, then yes, ... i have a 2006Pontiac Grand prix and my temp. goes up to the ... crzgrl637 answered 6 months ago ...the cooling fans won't kick on then you will see gauge over heat.

Car Engine Overheating - Causes and Symptoms of Over ...

I assume you mean valve timing marks. See diagram below. I assume this is the 1.3 L4 engine
If you go here you will find a diagram by another expert.

I need a diagram on how to line up a timing belt for a 1996 chevy cavalier 2.4l

Timing belt routing diagrams for cars and trucks? Click the link below:--- http://technoanswers.blogspot.com/2011/10/timing-belt-routing-diagrams-for-cars.html

Drive belt routing diagrams for cars and trucks? Click this link below:--- http://technoanswers.blogspot.com/2011/10/drive-belt-routing-diagrams-for-cars.html

I think you should go for manual first after that it would be easy for you to solve your problem. I had visited this site past 2 months before for my vehicle and find it quite helpful may be you will also get something useful here
Best Manuals

pls send your complete email and the model /year of the vehicle. included the VIN number, then ill send diagram to your email

For Mazda Car 2005-06 Spark Plugs...

Inspection
Inspect the electrodes and ceramic insulator.Burned or worn electrodes may be caused by:

Advanced ignition timing Loose spark plug Plug heat range too hot Insufficient cooling
Fouled plug may be caused by:
Retarded ignition timing Oil in combustion chamber Incorrect spark plug gap
Plug heat range too cold Excessive idling/low speed running Clogged air cleaner element Deteriorated ignition coils
Do not adjust the gap of platinum tip plugs; replace the spark plug if the gap is out of specification. The gap should be 0.049-0.053 in. on all models except Mazdaspeed6 or 0.028-0.031 on Mazdaspeed6 models.

1. Replace the plug at the specified interval or if the center electrode is rounded.
2. Apply a small quantity of anti-seize compound to the plug threads, and screw the plugs into the cylinder head finger-tight.

Removal & Installation

1. Before servicing the vehicle, refer to the precautions section.
2. Remove the battery cover.
3. Disconnect the negative battery cable.
4. Remove the plug hole plate by lifting off and removing the plug hole plate from the installation areas (rubber and clips) as shown in the illustration.
   
5. Remove the front suspension tower bar (joint).
6. Remove the ignition coils.
7. Remove the spark plugs.

To install:

1. Installation is the reverse of removal, tighten the plugs to 8-10 ft. lbs. (10-14 Nm).

2.3L (L3) Engine

1. Before servicing the vehicle, refer to the precautions section.
2. Disconnect the negative battery cable.
3. Remove the ignition coils.
4. Remove the spark plugs.

To install:

1. Installation is the reverse of removal, tighten the plugs to 8-10 ft. lbs. (10-14 Nm).

Mazdaspeed6

1. Before servicing the vehicle, refer to the precautions section.
2. Disconnect the negative battery cable.
3. If equipped with a turbocharger, remove the charge air cooler.
4. Remove the ignition coils.
5. Remove the spark plugs.

To install:

1. Installation is the reverse of removal, tighten the plugs to 79-177 inch lbs. (9-20 Nm).

Good luck(remember rated and comment this help).

I dont think anyone can hear the wastegate open. It opens when there is overboost and just routes exhaust around the turbo You may have heard the over boost valve open and release pressure., but normally, it doesnt open unless there is a problem with the waste gate. Its like a back up in case the waste gate is bad, or disconnected. Does the engine have the same amount of power as it always has? If so everything should be OK.

http://www.ugnius.lt/mazda/

hmmmm lets see......while driving on the highway 80 to 85 mph in 6th gear I am just under 3000 rpms. do you even own a speed 6? *****? crappy AWD ? have you ever driving the car hard? really hard like my **** in ur ****? this is one of the best handling cars ive ever drivin in...... three 300 zx's- 1 TT...... turbo 240sx (ka24det)........grow the *******......

The only thing i agree on is the gas consumption (stock) is very bad...... after installing a cold air intake alone my gas mileage was much better ...and now i have test pipe and down pipe plus HKS ssq bov and my car sucks gas like a 1.6 liter honda civic.

try taking a turn like a man you ***** maybe your opinion would change