Question about Isuzu Rodeo

1 Answer

Trying to bleed the brakes on a Isuzu 2000 rodeo

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

Keep lots of fluid handy and get a helper. Open the reservoir and fill it up then get under the car and on the back side of each brake cylinder where the line connects there is a small valve that looks like a grease zerk. Have your helper pump the brakes until they have some pressure and hold pressure on the pedal while you loosen the valve ( you will need a 6 or 7mm wrench) fluid and some air will come spraying out and the pedal will go to the floor, have your helper maintain pressure on the pedal until you close the valve and do it again until no more air comes out with the fluid. Add more fluid to the reservoir and move to the next wheel, keep going until you have done all 4 and you are finished. My advise is to go one or two more times after the air is gone to be sure it is all out and remember to keep the reservoir full.

Or read the links below. http://www.popularmechanics.com/cars/how-to/maintenance/4213448 http://www.automedia.com/Brake_Bleeding/ccr20011001bb/1

Posted on Aug 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anti lock brake bleed


I would have the entire brake system checked out by certified brake technicians. Would not want to risk a "maybe now fixed" approach with brakes.

Mar 13, 2014 | 2000 Isuzu Rodeo

1 Answer

I have bleed the rear brakes multiple times but still get air and "soft" pedal requiring multiple pumpimg. How do I bleed them if they are anti lock brakes? 2000 Isuzu Rodeo


It's pretty much the exact same process just remove your abs relays/fuses
if the brake bleeding doesn't work it sounds like you may need a new master cylinder

Mar 13, 2014 | 1996 Plymouth Voyager

1 Answer

Trying to find leak in clutch system os 1993 rodeo need diagram


Did you bench bleed the master or slave cylinder ? Is Your Brake pedal Hard ? Could be your Brake booster . send image for more understanding of your problem

Feb 25, 2014 | 1993 Isuzu Rodeo

1 Answer

Problems with the brakes isuzu rodeo 2004?


http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80376053 Here's how to bleed.If it still doesn't help,your rear wheel cylinder or cylinders could be leaking,to check ,remove rear drums and inspect cylinders for leaks,if leaking,check your shoes for spillage,you may need to replace brake shoes,can cause them to get hot and crack.Also inspect inside of drum for wear.

Aug 15, 2012 | 2004 Isuzu Rodeo

1 Answer

Brake pads on spongy on the front wheels


have buddy/wife pump brakes and hold loosen bleeder screw in caliper when steady stream of fluid with no splats comes out recheck pedal feel remember to keep fluid topped off when bleeding

Feb 18, 2010 | 1997 Isuzu Rodeo

1 Answer

Replacing front brake line


its really easy your gonna need a line bender they are cheap about 10 to 15 dollars and some line and wrenches dont forget to get help bleeding the brake line after replacement.

May 22, 2009 | 1999 Isuzu Rodeo

1 Answer

Rear brakes might be locked up???


Firstly it might be an idea to release the brakes so you can get the vehicle to a suitable place for repair. Something has gone wrong in the brake master cylinder or the pressure valve (if fitted) although I suspect the former. The hydraulic pressure can be released by loosening the nut on the brake pipe that goes to the rear brakes or undoing the bleed nipples on the rear cylinders a couple of turns. Try to bleed the brakes enough to get them working and then drive to a place of repair. Otherwise remove the master cylinder, strip down and repair or replace.

May 22, 2009 | 2000 Isuzu Rodeo

1 Answer

2000 isuzu rodeo brake problems


your master cylinder is gone. when stopped apply pedal and hold let up slightly then reapply if pedal sinks to floor master is bad.

Nov 11, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...