Question about 2006 Ford F-250 Super Duty

Open Question

How to replace rear axle seal on a F250 - 2006 Ford F-250 Super Duty

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

  • 51 Answers

SOURCE: Left rear axle seal is leaking differental oil.

ok then here is the procedure  1 take off the axle nut
2 on the lower control arm you will find a large nut and bolt i belive the nut is a 21mm and the bolt side is an 18mm. this bolt is the one at the knuckle near the brakes. remove it
3 you will need to pull the knuckle out of the way or a helper to pull the knuckle out of the way so you can slip the axle out of the knuckle.( its a tight fit but there is room to slip it out.)
4 use a pry bar to pop the axle free of the diff. hosing its held in by a spring clip make sure the clip comes out with the axle if it gets stuck inside you will have to fish it out.
5 use a pry bar or screwdriver to pry seal out of housing then use a flat object that contacts the entire rim of the new seal so it can evenly be installed with out getting smashed and tap it in with a hammer. ( a good trick here is to use some grease and pack it into the new seal where the spring is this will prevent the spring from being shocked out of the seal during instalation . the spring keeps tension on the rubber in the seal so it stays tight to the shaft it is sealing.)
6 then revers the above steps. also make sure you are using the right gear lube it will most likely be 75w-140 but make sure you check your owners manual will tell you if it doesnt say on the diff cover. you can cause a lot of damage if you put in the wrong thing. and make sure  you feel the axle spring clip snap into place.
as a note there are two types of axle seals that are used on these so if the new seal looks different than the old seal then the folliowing will be important to you.the seals on these have been redesigned so if you axle has what looks like a cup or dust cover pressed onto the shaft where it goes into the diff the new style does not use this and it will prevent the axle form going in all the way so the spring clip will not lock in and you will have a leak. so you will have to remove it and install the axle without it.

Posted on Mar 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a rear drivers side bent axle on a 2006 f250 is it possible to replace the axle shaft or do I need to replace whole rear axle


Best to replace the whole; although just replacing the axle shaft can be the solution, but risky.

Aug 09, 2015 | Cars & Trucks

1 Answer

Replacing front axle seals and bearings


I replaced the left front bearings and seals a couple of months back. It is not a problem but be careful as you dismantle the system and of course the reassembly of same. Be sure to replace all bearings and seals as you probably don't want to do this job twice at the cost of parts. No special tricks and relatively easy job. 1601d678-bcb0-4cc6-af13-c2a57bf7d073.jpg

Jun 22, 2014 | 2001 Ford F-250 Super Duty

1 Answer

Rear axle seal leaking f250 6.0 4x4 2005


if you have a semi-floating axle ie an axle that the axle bearing is pressed on you have to remove the wheel, remove caliper if disc brakes and remove a retaining plate that holds the axle bearing in position. pull out the axle and the seal will be left in the axle housing. Replace and reverse procedures. If you have a full floating axle you have to remove the axle from the hub undo tha axle bearing nuts amnd if disc remove caliper or if drum pull the hub of the axle. The seal will be in the back of the hub as in a truck. you will need some mechanical knowledge so if you are unsure get a mechanic to advise you

Jan 22, 2013 | 2006 Ford F-250 Super Duty

1 Answer

How do you change rear axle seal on 1993 f 250


pull rear cover, pull center pin bolt out, pull pin, push axle in to drop clip, pull axle out, remove old seal, install new one and reverse above

Jun 03, 2011 | 1993 Ford F250

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

1 Answer

Rear axle leaking fluid on to brakes


The axle needs to be removed to replace the seal behind the flange.this is not expensive but requires opening the rearend cover.So you will also need a gasket for the differential and some new gearlube.

Sep 06, 2009 | 1997 Ford F250 SuperCab

1 Answer

1986 F250 4X4 inner rear wheel seal is not stock


You can carefully remove the old sleeve, careful not to damage the surface underneath, inspect and assess the damage underneath. Possibly it can be repaired properly with medium then fine emery cloth polishing the surface. If there is a groove deep enough that your thumbnail catches on it, you might need to install a new sleeve. Research the brands and install the thinnest one possible. You may also be able to drive the seal in deeper or shallower to locate it in a different position on the spindle. It would only need 1/8 to 3/16" difference. Please post your results, hope this helps.
-Jeremy

Feb 08, 2009 | 1987 Ford F 250

2 Answers

Rear Axle Leak


if it is the seal, you will have to remove the caliper and rotor, remove the differential cover and remove the bolt and pin inside the diff carrier housing. push in the axle and remove the axle clip and pull out the axle use a seal puller or prybar to remove seal reverse the steps to assemble

Dec 10, 2008 | 2001 Lincoln Town Car

1 Answer

Pinion seal leaking


check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Oct 22, 2008 | 2004 Ford F250

Not finding what you are looking for?
2006 Ford F-250 Super Duty Logo

Related Topics:

3,739 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...