Question about 1995 Isuzu Trooper

Open Question

Having problems removing front rotors from my 95 isuzu trooper removed wheel, brake caliper, and hub, and still can off slide off front plate that bolts to actual wheel

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 26 Answers

SOURCE: 95 Suburban K2500 front brake rotor replacement

spray them with penatrant and smack the inside between the studs with a hammer they will brake loose

Posted on Nov 03, 2008

Ad
alicantecoli
  • 22156 Answers

SOURCE: 1995 isuzu trooper caliper removal

remove front wheel ,look at back of caliper and and look for teh two retaining bolts that hold the caliper to the support bracket.if not sure take it to a garage as any mistake could kill someone

Posted on Nov 15, 2008

pakis
  • 86 Answers

SOURCE: 1993 Isuzu Trooper auto locking hubs not engaging

Just have your auto - locking hub cleaned and use your 4wd more often, it get stock usually for non usage. dont use grease after cleaning, use oil or thick silicone oil.

Posted on Dec 05, 2008

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

dmsr63
  • 2050 Answers

SOURCE: 1994 Isuzu Pickup replace rotor, caliper, repack wheel barrings.

Remove caliper, then the caliper bracket that supports the pads and caliper. The rotot should have one or two threaded holes near the lug nut studs. You install a bolt here (Correct thread pitch) and thread it in to "pop" off the rotor. (They are usually rusted on.)
Keep in mind that the new caliper needs to have the brake fluid bled.

Posted on Oct 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year


  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Cv axle 4x4 diferencial


Make sure 2- wheel drive is selected.
Jack up the vehicle front and support on axle stands. Remove the wheel.
Remove the brake caliper. It bolts onto the hub carrier(aka knuckle) with 2 bolts from the vehicle side of the carrier so you cant see them without sticking your head into the wheel arch. Slide the caliper off the rotor and hub and hang it with a piece of wire inside the wheel arch. Dont let it hang on the pipe it is connected to. The caliper may be difficult to remove if the rotor has a ridge on its outer edge due to wear.
Remove ABS speed sensor(2 bolts to remove) behind the hub
Next comes the hub assembly. :
  • Shift on the fly:Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it.(On the piece of shaft now visible) and then you can pull off the hub flange. Remove the screw on the lock washer and then the washer itself. Remove the hub nut.The hub assembly(with rotor) will now pull off the shaft. Remove inner bearing and oil seal.
  • Manual hub: Select transmission 2H and "Free" on the hub. and run the vehicle about 100 m/300 ft.Remove 6 bolts on the cap then the cap itself. Next the snap ring/circlip and the shim behind it. Remove body assembly.
Remove the bottom ball joint on the hub carrier.(Ball joint removal tool may be needed to free the ball joint. Dont go hammering it. That will damage the thread) Swing the carrier upwards and you should have just enough free space to pull the shaft from the hub carrier. If not remove the top balljoint as well. Remove the clamp/SS strip from the inner CV rubber boot. Pull the boot back on the shaft. Remove the circlip from inside the DOJ case. The shaft can now be pulled from the DOJ case.
Remember to preload the wheel bearing on reassembly. Tighten the hubnut to 29 N.m. then loosen fully. Tighten again by hand. Connect a spring scale to the wheel stud. Pulling on the scale in the direction of rotation should give a reading of 2-2.5 kg/4.4-5.5 lb(new bearing) or 1.2-1.8kg/2.6-4 lb(used bearing) when the rotor starts to move. If it does not, tighten the hub nut a littl and measure again. Repeat till the correct measurement is achieved. See diagram.

2924189.jpg

Jul 21, 2010 | 1999 Isuzu Trooper

2 Answers

Noise coming from front brakes or wheel ,i change brake pads


Did you have the rotors turned? Did you check for rotor runout? Did you remove all rust from hub face and rotor mounting surface? Did you remove rust from caliper or pad slides? Lube all caliper and pad sliding surfaces? Are the pads application specific? Did you flush and bleed the fluid? Did you torque the wheels properly?

Feb 09, 2010 | 2005 Chevrolet Silverado 1500HD

1 Answer

95 isuzu troper 4x4 front break rotors or bad how do you take them off


1. jack up vechicle, support by jack stands
2. remove tire
3. remove bolts holding caliper
4. remove 2 bolts holding caliper bracket to spindle
5. slide rotor off
6. repeat in reverse order

Feb 05, 2010 | 1999 Isuzu Trooper

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

Replacing the front brake rotors


They have holes in that sit on your wheel studs.The wheels are the main restraint for the rotor with secondary restraint from you brake caliper.

Mar 21, 2009 | 1999 Isuzu Trooper

Not finding what you are looking for?
1995 Isuzu Trooper Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...