Question about 2004 Ford Freestar

1 Answer

My van has a misfire in 1 and 3 cylinder, where are 1 and 3 cylinder located infront or back?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

In the back #1 first from pass side

Posted on Aug 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair on a 2005 FORD E250 cargo Misfire emission level from at least 1 cylinder with three-way catalyst damage from at least 1 cylinder.


misfires are also from faulty injectors and low fuel pressures. from what you state I would be looking at those areas for the problem.

Feb 11, 2015 | 2005 Ford E-250 Van

1 Answer

Firing order for a 1999 nisson quest van


Believe it or not the firing order is 1-2-3-4-5-6 The cylinder locations are 2-4-6 in front by radiator, and 1-3-5 against the firewall. If you have a misfire on a certain cyl. and you've replaced the plugs,wires and cap and rotor, you probably have a fuel injector that's dead or plugged,it's common on Quests. Figure out which cyl. is misfiring and unplug the fuel inj. conn. with the engine running and listen for a change in RPMs. If there is no change then replace the injector.

Aug 15, 2014 | Cars & Trucks

1 Answer

Misfire on #4 cylinder when accerating on a 2005 renderous


I would start with switching a coil, swap # 4 coil to another spot and see if the misfire moves, the coils on this van operate to cylinders so move it and see if the misfire changes then you know its the coil and if it does not then next thing is to check spark plug and wire, replace the plug and wire and if that solves it then tune up van, good day,

Oct 14, 2012 | 2005 Buick Rendezvous

2 Answers

How many oxgen sensors does a 2004 Hyundai Santa Fe 2.7 2wheel drive vehicle have and where are they located? What idoes Bank 2 Sensor 1, Bank 1 Sensor 2, Bank 1 Sensor 1, and Bank 2 Sensor 2 mean?


you have 4 O2 sensors, bank one is the front cylinders ( close to the readiator ) there is 2 bank 1 O2 sensors one infront of the catalitic convertor ( bank 1 sensor 1 ) and one after the convertor ( bank 1 sensor 2 ) the same on the back cylinders they are bank two sensors 1 & 2 i will try to post the location of the wiring plugins if you find the plugs then you can folow the wiring to the sensor....good luck


johnjnail_106.jpg

johnjnail_107.jpg

johnjnail_108.jpg

johnjnail_109.jpg

Jul 01, 2011 | 2004 Hyundai Santa Fe

1 Answer

Town and county van with errors codes P 0300, P 0301, P 1494, P 1495 ???


P0300 - generic misfire.
P0301 - misfire at cylinder 1 = the spark was not generated at some time at cylinder 1
P1494 - Evap Leak Detection pump pressure switch condition = the ECM detected the leak detection pump switch did not change after the solenoid was energized
P1495 - leak detection pump solenoid circuit = the electrical circuit that commands the solenoid of the pump is interrupted
You need to check the wiring to the solenoid and the solenoid itself, located under the driver's side in the cast cradle under the steering gear. A good expertise of car electrics is required for that, you will need a good repair shop.

Jun 13, 2011 | 2003 Chrysler Town & Country

1 Answer

1999 Ford E250 van Rough running


complete tune up plugs wires distributoe cap and rotor

Jan 24, 2009 | 1990 Ford F350

4 Answers

HI I HAVE A 2001 MAZDA TRIBUTE AND THE CODES PO301 AND PO303 CAME UP IN THE DIAGNOSTIC REPORT. THE CAR TURNS OFF WHEN I WARM IT UP IN THE MORNING IN THE COLD AND AFTER THAT ITS FINE I ALREADY CHANGED THE...


cylinder 1 misfire and low compression. Plugs and wires changed plus new fuel injectors. The engines still misses and no one can find the cause. When put on the computer it read misfire cylinder 1.

Dec 31, 2008 | 2004 Mazda Tribute

2 Answers

Need know which cylinder is number one on 2000 ford windstar 3.8


#1 plug is the 1st plug on passenger side by firewall

Nov 15, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...