Question about 1995 GMC Sierra C1500
Code 32\r\n1995 sierra 1500 5.7 engine no big issues, but service engine comes on after about 5 minutes checked code ... three flashes... two flashes trouble code 32
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Disconnect the battery for a minuit and turn on the light's to power down any electrical power. Reconnect the battery and that should clear the "servie engine light soon",but if there are any DTC codes, the "Service engine light" will come back on.
On board diagnostic (OBD) was designed on vehicles equipped with electronic fuel injection so you can generally retrieve the codes yourself. No need buying a scanner or running to any parts stores to check the Engine Light. This system is called obd1 and applies to most vehicles made before 1995 for domestics and 1993 on imports.
For GM domestic vehicles made before 1995, the diagnostic connector is located under the dash panel by the driver side. To get the check engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink. All codes should start with code 12 which is one long flash followed by 2 short flashes. This code 12 means the diagnostic system is normal and will repeat itself continuously if there are no trouble codes. Otherwise, code 12 will flash 3 times before flashing the fault codes.
the codes can be erased or cleared by disconnecting the battery negative terminal for 1 minute and reconnect. Just make sure to check your service manual in case you have electronic equipment such as radio or clock that needs reprogramming in which battery disconnection is not recommended. Finally after performing repairs on the culprit code, always go for a road test to confirm if the problem is fixed.
Good luck and hope this help, here is a link to the DTC codes. http://www.gmtuners.com/OBD1_DTC.htm
Posted on May 08, 2009
This could be a number of things, that is why it is a good idea to have the engine codes read which many part stores offer for free.
The service engine light will go off if there is vaccum leaks, faulty sensors or circuits, or any electrical problems
Posted on Aug 24, 2009
SOURCE: check engine light on
Please check the fuel line for leakage. If there are no leakages, verify that your fuel tank cover is well fixed.
Posted on Dec 18, 2009
Testimonial: "THANK YOU I'LL TRY LOOKING AT THOUGHS ITEMS AND MAYBE REPLACING THE GAS CAP "
OK, if you have a misfire at a high rate of speed and it is intermittent, I wouldn't worry about it unless it makes the engine lose power or affects gas mileage.
If you want the engine to work perfectly, however, I would find out which cylinder is missing, and correct the problem by replacing coil packs or what not until it doesn't do this anymore.
Also, a bad O2 sensor can cause a 'random' mix that may come and go over time.
Posted on Aug 20, 2010
Tips for a great answer:
Dec 11, 2015 | 2004 Chevrolet Silverado 3500
Nov 01, 2012 | 1994 GMC Sierra
Apr 02, 2011 | GMC K1500 Cars & Trucks
Jun 07, 2010 | 2006 GMC Sierra 1500 2WD
Aug 24, 2009 | GMC Sierra 1500 Cars & Trucks
Nov 05, 2008 | 1990 GMC Sierra
Aug 12, 2014 | 1995 GMC Sierra C1500
87 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: