Question about 2004 Nissan Frontier

Open Question

Where is the knock sensor located need diagram

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

Ad
ZJLimited
  • 17970 Answers

SOURCE: I need to know the exact location of the knock

The knock sensor is located under the intake manifold on the passenger side of the engine. It can be accessed from under the vehicle. Look above and to the slight left of the oil filter on the back of the engine.

Sorry, but i dont have any diagram or pic about this.

Hoep helps with this details. Good luck.

Posted on Nov 11, 2010

ldtrisch
  • 83 Answers

SOURCE: I need a diagram to

ldtrisch_2.jpgHope this helps!!!

Posted on Mar 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram knock sensor location


Here's a link to the knock sensor.

May 15, 2013 | 2004 Mazda 6

1 Answer

Where are the knock sensor located on 2001 chevrolet silverado 1500 4.8 located at




  1. Raise and safely support the vehicle.
  2. Remove the tire to ease access to the knock sensor.
  3. Remove knock sensor shield
  4. Remove the connector from the knock sensor.
  5. Remove the sensor mounting bolt,
  6. Now remove the knock senor.
  7. To install reverse the steps above and tighten the bolt to 18 pounds torque.
  8. See diagrams for additional help. Note there is one on each side of the engine.

ironfist109_205.jpg

ironfist109_206.jpg

ironfist109_207.jpg


  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 30, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Need location of the knock sensor on the engine need picture or engine diagram


Hi!!
The Knock Sensor is located on the right side of the engine block, right below the exhaust manifold. See #7 on picture below:
1kbron_120.jpg

Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Mar 16, 2011 | 2002 Chevrolet Avalanche

1 Answer

Need to know how to install knock sensors and where they are need diagram. 2005 expedition 5.4 engine


Hello adamjerkins,

It is somewhat complicated to change the knock sensors. There are two of them and they are located under the intake manifold. The intake manifold must be removed. I would recommend tha you replace both while you have the engine apart.

What leads you to believe the knock sensors are bad, I've seen few bad knock sensors? The knock sensor issues more times than not have been caused by other problems.

After you remove the intake manifold disconnect the knock sensor connectors. Remove the bolts and the two knock sensors then replace with new knock sensors tighten the bolts to 15 foot pounds. Reinstall manifold. The total job for an experienced mechanic with tools is about 5 hours. Not a good job for a beginner.


Regards,
netvan

Mar 05, 2011 | 2005 Ford Expedition

3 Answers

Diagram available for 01 Nissan Xterra Knock Sensor location?


V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Feb 08, 2010 | 2001 Nissan Xterra

1 Answer

Knock sensor location


HI, click the link below to be directed to a full diagram that will show you the actual location of the sensor. 718 will be the actual sensor to extract and 739 is the mounting screw for the KS.

KNOCK SENSOR DIAGRAM

Jul 22, 2009 | 2001 Chevrolet Silverado

1 Answer

Knock sensor malfunction?


knock sensor is on the block, looks like a bolt and has 2 wires coming out of it.

Jun 22, 2009 | 2007 Jeep Commander Rocky Mountain

1 Answer

Diagram or location of knock sensor


Look under exhaust manifold on drivers side, closer to rear of engine . mounted on engine block.

Jun 01, 2009 | 1995 Jeep Cherokee

Not finding what you are looking for?
2004 Nissan Frontier Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...