Question about 1993 Jeep Grand Cherokee

1 Answer

I changed fuel pump and fuel filter truck started an ran. I turned it off an on 4 times to make sure it would run, it did. I put it back together and now it starts but won't stay running? Please help, thanks , ronnie.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Replace the oxygen sensor. Worked for me! My 1993 Jeep Grand Cherokee was doing this same thing, even after replacing the battery, crankshaft sensor, computer, ignition coil, wires and plugs and fixing vacuum leaks.

Posted on Aug 27, 2010

  • vickivelaz Aug 27, 2010

    Replace the oxygen sensor. Worked for me! My 1993 Jeep Grand Cherokee
    was doing this same thing, even after replacing the battery, crankshaft
    sensor, computer, ignition coil, wires and plugs and fixing vacuum
    leaks.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 vw jetta 2.0 4 cyl auto changed water pump timing belt driven put back together ran rough like out of time. put cam and crank at tdc per markings. engine rotates when key turned but dont start. just...


Did you remember to reconnect your Cam Position Sensor after putting it all back together? One tooth off shouldn't have bent a valve (but pressure checking cylinder will answer that). Did you check TDC once the belt is tight?

Aug 06, 2013 | 1999 Volkswagen Jetta

1 Answer

2010 ford mondeo diesel wont start after changing fuel filter, please help!


on a ford mondeo 08 the fuel filter is at the rear of car u take old filter put in new one fill with fuel put back together then put a pipe on feed [there might be a bleed niple on top that will be easier] suck till fuel comes out conect pipe back turn ignition on for 15 seconds 3 times to clear air then start done

May 20, 2012 | Cars & Trucks

1 Answer

My fuel pump seams to work when it wants to. I've rebuilt the throttle body and put it back on and the truck started back up and ran steady. I then saw a leak at the top of the throttle body and shut the...


turn key on wait 5 seconds turn key off do it again do this 3 or 4 times you should hear pump run for 5 seconds if it starts after that then your fuel pump is getting weak and needs to be changed

Sep 19, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

My 1995 gmc suburbans service engine soon light comes on only after i drive on the freeway when i turn the car off than turn it back on the light goes out. i have just changed oil and filter problem began...


hi reset it by disconnecting the live battery connection for3 mins then re connect that has done it for me if this helps please rate it thanks

Nov 21, 2009 | 1995 GMC Suburban

3 Answers

04' Sedona ran out of gas- now won't stay running


fuel pump is burned out from running out of gas, the pump is cooled by the gas it sits in inside the fuel tank, when you run low on fuel or out of gas you over heat the pump severely and the bearings in the pump seize up, have seen it dozens of times in my 30 years of dealer work.

Jun 15, 2009 | 2004 Kia Sedona

1 Answer

1989 ford e 150 fuel poblem


check the module located on the side of the distributor. I have had that problem and that was the ticket. Fords are common for that sort of failure.

Apr 06, 2009 | 2007 Ford E-150 XLT Wagon

1 Answer

1997 GMC K1500 4x4 5.7 ex.cab SFI injection system


I would check the fuel lines themselves and make sure there is no blockage. If not you might want to check your fuel injectors and see if they need to be replaced. also make sure you didnt install fuel filter backwards.

Nov 20, 2008 | 1995 GMC Jimmy

3 Answers

1997 GMC K1500 4x4 5.7 ex.cab SFI injection system


fuel pump died replaced it truck ran poorly afterwards. Had a prussuer test done pump determend pump was no good. Put in another ran good for 2 days started running poorly hard to start no power. 2nd fuel pump. So i figure another bad new fuel pump wow changed it put in a third brand new fuel pump. Still will not eve start now. I had it tuned up 2 months ago new plugs rotor, cap, etc. put in a new fuel filter made sure it is on proper checked all connections for leaks. this cannot be a fuel pump problem now. no problem with the elctrical i figure i have great spark on ignition tester. I can hear the fuel pump prime when i turn the key. but when i went and checked the fuel port i had no pressure. When it is being cranked gas sews out of the test port. Also i dont if this is comon cause i used to turn my keyand go. but when i have someone turn the key and i listen at the gas tank whn the key is shut off i hear gs spraying back into the gas tank. So i am open for opinions.

May 18, 2008 | 1993 GMC Sierra K1500

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...