Question about 2001 Toyota Sienna

Open Question

Code p1351 on toyota sienna having trouble with car idling very low then sometimes just cutting off unless foot is on gas pedal

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 01 hyundai Elentra idling issues

i had the same thing with my 01 elantra. i took it in and they had to replace the gasket on the air intake manifold. cost about CD$700

Posted on Nov 14, 2009

Ad
  • 1861 Answers

SOURCE: toyota 1998 sienna foot break light indicator on

The brake fluid level in your master cuylinder reservoir is low.

Posted on Jan 17, 2009

  • 6982 Answers

SOURCE: wont hold idle will start with foot depressing gas pedal will run with foot on gas but stalls when foot removed

Check and clean Idle air control valve. Make sure its responding to signal as well. Also make sure ther are no vacuum hoses disconnected. This may not be a "cure" but it's a good place to start.

Posted on Apr 14, 2009

  • 53 Answers

SOURCE: 2003 toyota sienna idle problem

After about 100K + miles the idle air control valve (IAC) begins to collect carbon deposits that interfere with the movement of the spring-loaded valve. You will not be able to clean this without removal and dissembly of the IAC body. Use an emory cloth or fine sandpaper to remove the build up around the valve. This should free it up to rotate without binding. This is a temporary fix, of course, and will either require cleaning again or replacement of the valve. Getting to the IAC requires removal of most of the intake upto, but not including, the intake manifold. Total time is approximately 3-4 hours, but worth it. Good luck, and I hope this helps.

Posted on Feb 21, 2010

  • 31 Answers

SOURCE: My 2000 Land Rover Discovery II doesn't start

The second cable should be for cruise control. Your problem sounds like either a vacuum leak (air entering the engine unmeasured by the air sensor), or fuel vapor in the fuel rail. A vacuum leak can be determined by spraying starting fluid at the air intake hoses, plenum,and connections while the engine is idyling and noting where the engine accelerates to determine where the vacuum is leaking (unmetered air is entering) from. Tighten or replace gasket,hose,seals etc. Bleed the air on the fuel rail if needed with care.

Posted on Aug 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine revs up down while in idle


If its been without the line for over a year, I Highly doubt it. Look into IAC valve. Most are installed with 2 screws, easy to adjust. Idle Air Control Valve. Look that up, for a start.

Apr 15, 2014 | Toyota Matrix Cars & Trucks

1 Answer

Car wont stay running when foot off gas


sounds to me like your catalytic converter may be clogged.

Feb 17, 2014 | Ford Escape Cars & Trucks

1 Answer

Gas pedal stuck open


lube-oil the peddle and cable-do both ends of the cable-check the return spring -it may be weak-you may want to replace it-cheers Denny

Nov 22, 2013 | Jeep Cherokee Cars & Trucks

1 Answer

Engine wont start, unless I push the gas pedal and keep my foot on it.?


Could be a dirty throttle body, or a stuck idle air control valve.
Is the check engine light staying on now ?

Apr 23, 2013 | Toyota Highlander Cars & Trucks

2 Answers

Toyota avanza controll reve counter


Hi

i have a Toyota Avanza 1.5 sx. been driving it since 2007 without problems

early this year the reve started mulfunctioning. it goes up and down in an idle mode. when it started it was cutting power as i stop.
took it to Toyota dealer 3x they could not identify the problem. its now better and like in the morn8ing when i start it it goes to 3000 revers and after a while drops down to 1000rerves. this problem is still happening like once in two days or once everyday of idling up and down

please help

Oct 29, 2011 | 2007 Toyota Sienna

1 Answer

I have a 2000 ford explorer limited edition 5.0L V8.. The vehicle starts fine but after a while at idle it will sometimes die slowly.. if i put it in gear it also wants to die out. if I hold my foot on...


Hi, this problem can be caused by a broken fuel pressure regulator diaphragm. With the engine running, remove the vacuum line from the regulator. If gas comes out of the regulator at the vacuum port, replace the regulator.

Jun 24, 2017 | Ford Explorer Cars & Trucks

2 Answers

1997 ford expedition will start but wont stay running unless you hold your foot on the gas pedal. Replaced mass airflow sensor because that's the code that came up. Doesn't do it all the time.


if code keeps coming up re check sensor and connections and if not done replace air filter ----if good than check fuel prssure sometimes clodding fuel filter can cause same problem and set off sensor

Jan 04, 2011 | Ford Expedition Cars & Trucks

1 Answer

My toyota hilux surf 1992 auto, 3L 4x4, keeps cutting out when i put it in reverse and drive. sometimes it will go for a couple of minutes then just cut out randomlly. whats wrong with it and how do i fix...


Sounds like the idle is too low. This could be due to a bad vaccuum line or a faulty IAC if this car has fuel injection. IAC = Idle Air Control motor. Check for loose or broken vaccuum lines first. If no vacuum are bad and you can keep the car running by keeping your foot on the gas a little and dies when you let the gas pedal up then I would think the IAC is bad. A poor idle can also be the result of a long overdue tune up.

Nov 16, 2010 | Toyota 4Runner Cars & Trucks

1 Answer

P1346 and p1351 code from toyota sienna 2001, new timing belt


yes your out on the timing marks, set it to zero remove the top cover and check the marks

Apr 04, 2009 | 2001 Toyota Sienna

2 Answers

Engine wont idle unless you keep your foot on the gas pedal


First, try a new accelerator pump. They're less than $10 and easy to install. On the side of the carburator, near the linkage. It's simple a small rubber diaphragm.

Mar 15, 2009 | 2001 Toyota Tacoma

Not finding what you are looking for?
2001 Toyota Sienna Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...