Question about 1998 Plymouth Voyager

1 Answer

How do i get to the water pump? i cant get the crank pully off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Ah, The serpentineIt's easy and doesn't require a prybar. Here's how:

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded 'tensioner' arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
The same technique is used to get the belt on

Hope this helps

Best regards

Mike

Posted on Aug 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I installed a new powersteering pump on a 88 gmc k1500, now it eats serpentine belts cant get the pullies lined up right how do i fix?


I would install a reman pump,never try & remove a pully
The pump wasn't the problem

Your problem is most likely that the crank damper has
worn & moved. The rubber in it is the issue & it is hard
to see any misalignment

Jun 13, 2012 | Cars & Trucks

1 Answer

Olds 307 Belt Diagram


307's have a unusual routing, it's easy to get confused.

From back to front:
1) Crank - Water Pump - Air Conditioning
2) Crank - Power Steering - Water Pump
3) There are two versions, depending on how many grooves the power steering pump has:
(1-groove P/S):Water Pump - Alternator
(2-groove P/S):Crank - Power steering - Alternator - Water pump
4) Crank - Air Pump

May 14, 2012 | Cars & Trucks

1 Answer

WHERE IS THE WATER PUMP LOCATED...2003 ELANTRA


hi from uk fortunately the water pump on your car is not driven by cambelt ! the pump is driven by serp belt the pumps location is = if you look at front of engine view from front wing as you look down front you will see a large pully on left of cambelt covers and this is the water pump access to pump is best by supporting car and removing wheel and then the under wing cover that is secured by screws some advice for you if you intend renewing pump the pump pully is secured by 4 bolts use a 10 mm cranked ring spanner or socket loosen these bolts before you remove the drivebelt as belt holds pully and helps to prevent pully turning as you try to loosen these bolts hope this helps ?

Jan 26, 2010 | Hyundai Motor 2003 Elantra

2 Answers

Antifreeze drips from crank shaft pully area when running.


it's probably not dripping from the crankshaft... it would drip from the water pump just on top of it...

to check if it is done, take a flashlight and spot on top of the water pump. there should be a hole on top of it behind the pulley...

if it is damp, the pump is gone....

if not it might leak from the gasket...

Apr 28, 2009 | 1986 Acura Integra

1 Answer

Cant put on belt right


from front of engine looking back,belt around bottom of crank pully,water pump is just above,left side of belt comes around water pump going counter clock wise,put belt over alternator,then straight across to a/c compressor,(make sure belt goes under any idler pullies,smooth side of belt to smooth side of pully)find your belt tensioner,pry back on tensioner(be carefull)and carefully place belt under roller pully of the tensioner,release and check allignment of belt prior to starting.oh ya make sure belt is in good condition.

Mar 01, 2009 | 1991 Chevrolet C1500

1 Answer

Crankshaft pully is rubbing off fan blades


sounds like your water pump is bad does the fan move in and out if you pull on it or the crank bolt fell out and the pully is comming off ill bet on the water pump being bad

Dec 03, 2008 | 1996 Jeep Grand Cherokee

1 Answer

Surpentine belt.


depends on which v8 you have....the 4.7 the routing is as follows it goes under the waterpump pully over the alternator down and around the power steering pumpto the crank...it goes under the bottom of the crank to the idler pully.the flat side of the belt goes ver the idler then around the automatic tensioner to the ac compressor.
on the 5.2 and 5.9 it routes starting at the idler pully the flat side goes undr the idler the up to the ac compressor around the compressor and down to the power steering pump ... around power stering pump to waterpump where the flat side is against waterpump pully around water pump down and around crank up it automatic tensioner....around tensioner and up and over alternator

Nov 30, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
1998 Plymouth Voyager Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...