Question about 1984 Nissan Pickup

Open Question

How do I put my timing chain back on my 1984 4x4 nissan pickup 2.4 engine?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: 1987 Nissan Pickup Truck Will not start it will crank. So i Did Tune up With wires spark plugs I Don't know the order of last 2 wires that go in center of dist cap. Please help and will this solve thi

I'll send you 2 pictures, 1 will be your engine. I picture in each post.b72a24f.jpg

Posted on Jun 02, 2009

Testimonial: "thank you"

pal03246
  • 705 Answers

SOURCE: timing chain wear

That is correct. If your engine is whinning at about 2000 rpm's and its a high pitch whine, you need upper timing chains and chain tensioners. aka plastic gizmo as you called it. The timing chains ride off the plastic portion of the tensioner causing the noise, basically the chain is riding on steal stub from within the tensioner, that's where the noise is coming from. Waranree on this is 5years or 60000 miles which ever comes first. And the new tensioners are updated parts.

Posted on Jul 23, 2008

pal03246
  • 705 Answers

SOURCE: Trying to put timing chain

no adjustment neccesary. There is a timing chain tensioner, which you will simply push back in to its body. once you do that, there should be a small hple somewhere on the body of the tensioner. That' sthere so you can piut a paper clip into it to keep the tensioner from coming out. Once you lock that in place you can remove the tensioner and than the timing chain.Once you get it all back together, just pull back on the pin and the tensioner will come out and put tension on the chain. good luck.

Posted on Jul 24, 2008

messstat
  • 365 Answers

SOURCE: i need to install my timing

If you get it wrong...the valves are TOAST. TGry a Chiltons (AutoZone NAPA) but I would pay a mechanic ($80-125) to install it and get it running.

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my 1996 nissan pickup start after changing the oil pump


Hi Bryan, I'm Al the owner of Big As Auto Repair

Bryan, If you changed the oil pump on your 1996 Nissan Pickup and it involved removing the timing chain then I would say you did not get the timing set back up correctly and hopefully you do not have the interference engine because if you do you possibly could have bent the valves in the head. This can be costly. Here's what I need to know. Did you remove the timing chain to do the oil pump? If you did send the engine size to my website below through "Contact Us" and I'll see if your engine is a interference engine. We may be able to work together and get you out of this mess. Have an awesome day Bryan! Auto Repair

Feb 16, 2015 | 1996 Nissan Pickup

1 Answer

1994 nissan pu starter drags when engine is warm, new starter,new battery. new timing chain & gear, valve job,head gasket


1. Make sure all the high-current battery and starter connections are clean and shiny. Don't just wipe them off; get one of those battery terminal cleaners that scrapes off the top layer of oxidation. Use a wire brush on connections the battery cleaner doesn't fit. Remove each connection, clean it and put it back.

2. Be sure the timing is set correctly.

3. If there was a heat shield on the starter, make sure it's still there.

4. Get the starting system checked at an auto parts store. Maybe you got a bad battery or starter.

Jan 18, 2015 | 1994 Nissan Pickup

1 Answer

1985 nissan pickup. How to replace the head gasket without touching the timing chain?


as long as the timing chain is not in your way ,,it should be pretty simple ,,but if it is remove your timing cover and loosen the timing chain tensioner ..make sure you put that chain back on properly on the proper timing marks

Oct 23, 2013 | Cars & Trucks

1 Answer

Intermittent Rattling & Cylinder Miss On 95 Nissan 2.4L 4 Cyl


Yes, it COULD be a timing chain rattling, but again, your guess is probably better than mine at this point.

Without the ability to hear the noise it is impossible to say. Noises can be very difficult to locate when you are standing right in front of the vehicle. It is completely unachievable to perform this task remotely.

Are you sure it is coming from the engine and not the transmission? Or maybe even the exhaust? It is not likely for a timing chain noise to go away as a reult of putting the transmission in gear.

As for the misfire, when does it occur? is it at idle? Is it when you are accelerating (putting the engine under a load? Does it only misfire at high speeds? Much more info needed here.

May 04, 2012 | Nissan Cars & Trucks

2 Answers

This 2002 nissan 2400 pickup has had the timing chin replace by my mechanic. he swears up and down he did it correctly. After letting another mechanic so-call mechanic took the carburetor screws in and...


Hi, your diagram is below. Also threw in the timing marks. Not sure how hard it is to get the top cover off the timing chain as I have not worked on this engine. If you could get a peek at those timing marks you could verify valve timing. Let me know if you have more questions, and thanks for using FixYa.

jturcotte_806.gif

jturcotte_807.gif

Jan 11, 2011 | 1997 Nissan Pickup

1 Answer

Tears timing chain ajuster off nissan1989 four times


I'm assuming that you are talking about 1989 Nissan Truck 4WD 3.0L FI 6cyl.

In this models, the Z24i and KA24E engines do not use the pin counting method for finding correct valve timing. Instead, set the timing chain by aligning its mating marks with those of the crankshaft sprocket and camshaft sprocket. The camshaft sprocket should be installed by fitting the knock pin of the camshaft into its No. 2 hole. On the Z24i engine, the No. 2 timing mark must also be used.

Excatly, what is the problem? Adjuts timing procedure?

Sep 16, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

Timing on 1984 nissan pick-up just put back together timings off how to set?


is there any way to put and set timming chain back on after I have droped it and lost the markings

May 15, 2010 | 1984 Isuzu Pickup

1 Answer

1993 nissan pickup 2.4 liter back firing just rebuilt engine timing isnt 180 out distibuter isnt 180 out blowing embers out tailpipe and exhaust flutters


Loosen the valves up and reset valve clearance and since it is blowing out the exhaust there is 3 things it can be, timing belt, or chain or valves to tight or distrbutor is off. My guess is you put the chain on and it slipped 3 or 4 teeth and is backfireing threw the exhaust. If you need more help post here and I will help.

Aug 28, 2009 | 1987 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...