Question about Chevrolet Camaro

1 Answer

The water pump was bad soon this 94 Camaro that I just got so replaced it along w/the radiator hoses. After I flushed the cooling system,I filled it back up. I drove it around for a couple of days and noticed that it started to get kinda hot again, checked the fluid level whi h was low, topped it off, then noticed it was leaking out from between the block & the trans. I'm assuming that it's 1 or more of the freeze plugs on the back of the block because there are no other leaks to be found. How much trouble would it be to drop the transmission(since I've never messed w/a 5spd./torque arm combo on a camaro before) to replace those plugs? Thanks, Kev

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

This sounds like you have a leaking intake manifold. Not that uncommon for these cars. Hook a pressure tester to the system and grab a flaslight. A pressure tester can be borrowed from most autoparts stores. Apply pressure and start looking. If it is the intake, let me know and I will get you diagrams and instructions.

Posted on Aug 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anybody have a video link on how to flush the cooling system on a GM 3.1L SFI OHV 6cyl motor? I need a vid for this particular motor cause mine is still overheating & i have looked everywhere.


flushing a cooling system is the same method as any other motor

do it without the thermostat fitted
or water pump opening

sacrifice an old radiator hose to adapt a garden hose fitting
for radiator flush

air in system fix
your thermostat housing has no air bleed valve
no top radiator cap

old school way
heater on full
run motor till thermostats fully open
burp radiator hoses
wait till water is running up into over flow bottle without bubble
replace cap
turn off heater
correct level in over flow bottle

why still over heating
you fitted everything i would have ... yet still overheat
possibles
leaking inlet manifold gaskets
hose clamps loose
cooling fans spinning too slow
thermostatic fan switch faulty
aluminum radiator is a big one
air ..fins bent or some water channels blocked

or possible head gasket leak




26337512-0cp1kjor4xsfh4zi1nnjocnr-4-0_0.jpg

26337512-0cp1kjor4xsfh4zi1nnjocnr-4-1.jpg

26337512-0cp1kjor4xsfh4zi1nnjocnr-4-3.jpg

26337512-0cp1kjor4xsfh4zi1nnjocnr-4-6.jpg

Nov 02, 2016 | Cars & Trucks

1 Answer

1996 nissan altima no cabin heat, new radiator, flushed and filled, top hose hot, lower hose cold, newer thermostat checked good


HI Anon.
Remove your radiator cap (WHEN ENGINE IS COLD), run the motor and let it warm up a minute or two, have someone rev the engine a little while looking into the radiator. If the water goes down and/or you see the water moving, your water pump is good. If not this means that your water pump is bad and is not moving enough water through the system. Try Removing your thermostat and run the engine without it. Keep checking the radiator hoses to see if they are the same temperature. If they are not the same temperature the water pump is bad. If they are the same temperature your thermostat is more than likely the culprit. Hope this helps.

May 30, 2017 | Nissan Cars & Trucks

1 Answer

Our Durango is a loaded towing, 360 with heavy duty water cooling system. The radiator was replace before we bought it. We have put all new hoses, thermostat (2) new water pump, new cap(2) had it cle


When you fill the radiator, did you make sure the car heater was set to Full Hot? If not, there could be an airlock in the water system. This can give the symptoms you describe.

May 05, 2013 | 2000 Dodge Durango

1 Answer

Overheating?


Thermostat temperature senecer needs to be replaced

Nov 24, 2012 | Cars & Trucks

2 Answers

I have an 1997 chevy camro rs w a 134000 miles that is overheating the engine an water pump has been replaced an i stil cant find what is causing it to overheat


It could be the thermostat not opening and closing as it should. Or it could be a bad overflow/radiator cap. If the cap starts to go bad, it won't hold pressure and this will cause overheating. Good Luck. There are other major issues possible, but hopefully it's not. Start the engine cold and as the engine warms you should feel the thermostat open and water flowing as you hold the radiator hose, just be careful around moving fans.

May 13, 2011 | 1997 Chevrolet Camaro

3 Answers

04 Chev. Avalanche 1500 Z71 5.3 125K mi. Temp gauge reads erratic from 210 to 245 or so. heat blows warm then cold. Coolant level, OK. I have been told could be sticky thermostat but usually is restricted...


Normally the engine operates at 195F, if you did not replaced thermostat with another one at 185F. If the temperature has a tendency to rise up, the reason is a partially obstructed cooling system or/and a bad thermostat.
The first part of the cooling system that gives up is the heater core, because the coolant flowing channels are thin. You got a good advice but not the best one. It is the time for a coolant flush in your car. To do do it right then you need time. Plan ahead for a week end. With a cooled engine, start as your friend advised you with the heater core hoses. Disconnect both of them, but the dirt has to go out of your car, so with a garden hose back flush it and let the dirt to get out of your cooling system. After you will get clean discharge, it is the time for coolant bottle, remove it, discharge the used coolant and clean it. The third to come is the radiator. Open the drain cook, or disconnect the lower radiator hose, and disposal used coolant properly. Now open the radiator cap and flush with water the radiator till discharge will be clear. You think that you are done? Not yet. There is half of old dirty coolant trapped in the system.
Install everything, and connect all coolant system hoses, radiator, heater core and coolant bottle. Now you have to run your car with water. Fill out the cooling system with distilled water, start engine, turn on the heater high, and run till upper radiator hose get hot. That means the thermostat opens.
Let the engine to cool down, open the radiator cap, and draining cook or lover radiator hose and drain everything. You can use flush detergent if you wanted at this stage, but flushing with detergent will add 4 more hours, because detergent is colorless and you have to guess how many fill and drain processes do do to get rid of it. I do not do it, but if your cooling system is very dirty you have to do it. After the last drain, fill the cooling system with concentrated antifreeze and 30% distilled water. The reason is because it is more water trapped inside the cooling system. The goal is to reach 50/50 concentration. You need a coolant tester to find this. Start the engine and add coolant til radiator is full. Install the radiator cap and bleed the system. After driving you car for a day or so, let engine to cool down, open the radiator cap check the concentration of coolant with the tester and add antifreeze or distilled water as necessary. It is a good idea to replace the thermostat while flushing the radiator. This procedure has to be done every 2 to 3 years. It is up to you to decide to use RED GM Dex-Cool or GREEN Prestone antifreeze.
In all my cars I have replaced Dex-Cool with Prestone, but I flush the system every 2 years, and I never had a cooling system problem in all my cars.

Nov 14, 2010 | 2004 Chevrolet Avalanche

1 Answer

How to change radiator 1998 oldmobile intrigue


Hope this helps you. Here are the basics. There are many problems you may run up against (frozen bolts, stubborn or cracked hoses, rusted clamps, etc)that may need to be fixed or replaced before proceeding: SHut off engine, allow to cool completely. Disconnect the cooling fan, remove negative battery terminal connection. Drain radiator by opening draincock and/or removing lower radiator hose, collecting coolant in a drain pan. Do not let it go onto the ground - bad for environment! Open top radiator hose to allow remainder of coolant to flow out. A few quarts of coolant will remain in the engine block. You will want to totally flush and refill AFTER replacing the radiator to get all the crud out of the system. Unbolt radiator and disconnect any other items still attached (transmission cooler, temp sensor wires, etc.). Remove radiator and replace with new, reattaching all items removed from old radiator. Inspect other items and possibly replace suspects. Reattach hoses and make sure the clamps are tightened without pinching hoses excessively. Do a flush job with water/radiator flush, making sure the water runs clear out the draincock. Instructions for flushing the cooling system are usually printed on the radiator flush bottle. Be sure the heater is on and the engine warms up completely to open the thermostat. SHut off engine and drain as much water as will leave. Fill with 50% coolant mix (Dexcool or equivalent). Estimate water remaining in the engine and add 100% coolant to balance. COmplete fill with 50% mix. Remove air by running engine until warmed with the radiator cap off, adding coolant mix along the way.

Oct 09, 2009 | 1998 Oldsmobile Intrigue

3 Answers

1997 Camaro is overheating. I have replaced both the Water Pump and Thermostat and still overheating


what do you mean by overheating? puking coolant out? or just high on the temp gauge. the rad fan should come on if the a/c is on. if the a.c is off, the fan doesnt come on till 220f or so. when the fan is on, there should be "roasting hot" air blowing through the radiator, if not the radiator is not flowing coolant.

Sep 18, 2009 | 1997 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...