Question about 2000 Dodge Ram 1500 Truck

1 Answer

My 2000 Dodge Ram 1500 stalls out while I'm driving and a No Bus signal comes on the odometer reading. It starts again usually after a few minutes but how can I fix this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 131 Answers

I had a jeep that flashed that and wouldnt start i ended up replacing the pcm(engine computer) after checking the wire harness and connection if im not mistaken the pcm is in a place where it can be exposed to water so it might have water damage hard to tell without the truck but the bus signal is a state of health from the computer like a self diagnostic of it so without the signal it wont run hope this helps good luck

Posted on Aug 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starts and shuts off when I stop at stop sign or light.


dodge dakota idling and dying - CarGurus

www.cargurus.com > Questions > Dodge > Dakota

CarGurusApr 12, 2011 - dodge dakota idling and dying - My dakota will start then idle down and die. ... I have a 1992 dodge dakota that dies on me at stop signs and when I take my foot off the gas pedal. ... Had the same problem with my 98 Dakota.

Dodge Ram 1500 Questions - 1998 1500 5.2 Shuts Off ...

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusAug 29, 2011 - 1998 1500 5.2 Shuts Off Randomly - does anyone have an answer to the mysterious shutting ... 1998 1500 5.2 that shuts off randomly and if i wait a few seconds to minutes it will start again. ... does it do it when coming to a stop or when taking off from a stop or shifting from drive to .... Used Dodge Dakota".

Truck Shuts Off - 1998 Dodge Dakota - RepairPal

repairpal.com > Questions > Dodge > Dakota > 1998 Dodge Dakota
I have a 91 dodge dakota truck with a 318 motor, 249,000 miles, it will start up thenshut right off when I take my foot off the gas pedal, I had a tune up a month ...

2000 Dodge Dakota idle then dying problem FIXED - YouTube

? 4:05
https://www.youtube.com/watch?v=XRVQEdnei34
Mar 26, 2014 - Uploaded by AoDMADPenny
It would rev up then back down to about 200 rpm then just shut off. ... My Dakota dies during idling right after i start it up and then it wont start back up again. .... 1998 Dodge Durango No Start or No Bus or Randomly Stalls ...

Jan 06, 2016 | 1998 Dodge Dakota

1 Answer

00 Dodge Durango keeps stalling, getting no bus signal and transmission light


had the same issue 4months ago, it end up being the pcm, i hve a 2000 dodge durango as well

Aug 25, 2012 | 2000 Dodge Durango

1 Answer

2000 Dodge Ram 1500 V8 stalls while driving. After a few minutes it will restart. Not a fuel pump issue. Engine will turn but won't fire. Seems to take longer in hot weather. Any suggestions?


If this happens when you lay off the gas while driving then it could be the IAC.

The IAC (Idle Air Control) Sensor. My Dodge did the same thing and by either cleaning the IAC or replacing the IAC did the trick. I found a video for you on Youtube on how to replace it. The IAC is on the backside of the throttle body and only takes minutes to do. Mine was loaded with carbon and locked up.



http://www.youtube.com/watch?v=5yStBpngvbs

Jul 27, 2011 | 2000 Dodge Ram 1500 Truck

1 Answer

2000 dodge ram 1500 will not start, sometimes. engine turns over and "no bus" signal comes up on the odometer. If I leave the key on for several minutes, fuel pump eventually comes on and I can hear a...


If you are getting a 'no bus' signal and a no start, then you may have a sensor that is shorted. Start by disconnecting sensors on the vehicle one at a time and trying to start the vehicle after disconnecting each one, if it doesn't start, reconnect the one you've disconnected and disconnect another and try to start again. Start with your Oxygen sensors first and then move on from there. If this doesn't work then there is a problem in the circuit but I've seen this problem on numerous Chryslers and it usually is always a bad sensor. Once you isolate the bad sensor, replace it and problem should be fixed. Good luck.

Nov 03, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

2001 dodge ram 1500 5.9 4x4 motor turns over but will not start. ran fine the day before. the odometer reads no bus, check engine light comes on and gas gauge does not read now what could be causing...


First check is a look in the fuse box for a blown or loose fuse and also push all relays into their sockets. The check engine light shows that a trouble code is registered in the computer. Rent a scanner, read out any code(s), and pursue to repairs.

Sep 09, 2009 | 1999 Dodge Ram

2 Answers

No Bus Error


All the modules are connected together to communicate with each other via the PCI bus. It is possible that one of the modules is pulling the bus down.Since the vehicle won't start it could be any one of the modules. It will be a process of elimination to find the faulty one by disconnecting them one at a time. Here are a few, powertrain control module (the one you replaced) Instrument cluster, overhead console, anti-lock brakes, airbag. Since the cluster unplugged wont read anymore, just try to start the vehicle to see if that was the one. Otherwise see if the odometer message of "no bus" goes away after each one is unplugged.

Apr 23, 2009 | 1999 Dodge Durango

3 Answers

INSTRUMENT CLUSTER IS READING NO BUS AND NONE OF THE GAUGES ARE WORKING same problem,usually comes back on.


My gauges quit working on my 2000 Ram 1500 and while troubleshooting the problem I removed the DIN plug located in the fuse box underneath the hood. It is the one with a phillips head screw in it. I examined the conenectors and everthing appeared in order. I reseated the plug and tightened the screw back up. I cranked the truck and everthing worked perfectly. I suspect that the connectors may work loose over a period of time and noticed that when tightening the screw it made a slip when overtightened much like a locking gas cap. Tighten the screw until just before it slips. Hopefully this will help a lot of dissapointed Dodge owners.

Dec 23, 2008 | 2000 Dodge Ram 1500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

654 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...