Question about 1987 Chevrolet S-10 Pickup

Open Question

How to remove timing gears in 87 s10 - 1987 Chevrolet S-10 Pickup

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

87 chevy s10 brakes


Front or rear, they're both very easy to change if you go to YouTube you can get a step by step video on both.

Jul 02, 2016 | Cars & Trucks

1 Answer

Chevy 2.8 1993 s10' timing chain and gears installing


Replacing the chain and gears requires removing the water pump, dropping the oil pan, removing the balancer and timing cover. Rotate the crank so the dots on the cam gear and crank gear line up at the 6 and 12 o clock positions respectively. Unbolt the cam gear and remove it and the chain. If you need to remove the crank gear you can use a three jaw puller or something similar to pull it off. Reinstall the crank gear lining up the gear with the keyway on the crank and press it on with the appropriate tool. Install the cam gear with the chain and make sure dots line up again. It may be necessary to remove the valve covers and rocker arms as well to rotate the cam shaft if need be.

Jun 22, 2016 | Cars & Trucks

1 Answer

How can I remove gear-to-gear timing cam?


images for How to remove a gear to gear timing cam ...

DIY Timing Chain and Gears Removal - YouTube

? 6:31
https://www.youtube.com/watch?v=eMXO1bvUCMs
Dec 30, 2012 - Uploaded by Bullshitkorner
The most important part when doing timing gears on a engine is ... Doing this inside the engine bay will be a bit of a pain in the axx but it is doable for sure. ... How to build a Chevy 383 Part 3: How To Install a Cam & Timing ...

Head removal & replacement, Timing Chain & gears also ...

? 3:28
https://www.youtube.com/watch?v=CnXtwR1N0Og
Apr 28, 2012 - Uploaded by No1hmfic Gibson
Head removal & replacement, Timing Chain & gears also, 97 Chevy S10 2.2 ... replacing the head gasket in a chevy cavilier 2.2 liter 4 cylinder - Duration: 9:38. ... 98 S10 Vortec V6 4.3 Intake Gasket Replacement Part 1 of 5 ...

Chevy S 10 2.2 L Engine Timing Chain Replacement Guide ...

? 7:30
https://www.youtube.com/watch?v=8nX5HARPSF4


Feb 03, 2016 | 1998 Chevrolet S-10 Pickup

1 Answer

Where is crank censer located on a 1997 s10 truck?


the jeep wraangler is on the bell housing on the drivers side and can be addressed from under the drivers side behingd the front wheel. The S10 the cranks senser depends on the motor size and the year but if it's a 87 4.3 it's in the bottom of the timing cover just behinf the cranks shaft pulley for the belt drive.

Dec 12, 2010 | 1987 Jeep Wrangler

1 Answer

How to change a timming belt on honda civic


Timing Belt and Tensioner REMOVAL & INSTALLATION 1984–87 Engines
  1. Turn the crankshaft pulley until it is at Top Dead Center.
  2. Remove the pulley belt, water pump pulley, crankshaft pulley, and timing gear cover. Mark the direction of timing belt rotation.
  3. Loosen, but do not remove, the tensioner adjusting bolt and pivot bolt.
  4. Slide the timing belt off of the camshaft timing gear and the crankshaft pulley gear and remove it from the engine.
  5. To remove the camshaft timing gear pulley, first remove the center bolt and then remove the pulley with a pulley remover or a brass hammer. This can be accomplished by simply removing the timing belt upper cover, loosening the tensioner bolts, and sliding the timing belt off of the gear to expose the gear for removal. NOTE: If you remove the timing gear with the timing belt cover in place, be sure not to let the woodruff key fall inside the timing cover when removing the gear from the camshaft. Inspect the timing belt. Replace if over 90,000 miles old, if oil soaked (find source of oil leak also), or if worn on leading edges of belt teeth. Fig. 1: Timing belt and front cover assembly — 1984–87 engines 86833161.gif
    Fig. 2: Positioning the crankshaft and camshaft pulleys before installing the timing belt — 1984–87 engines 86833162.gif
    Fig. 3: Timing belt tension adjustment — 1984–87 engines 86833163.gif
    To install:
  6. Be sure to install the crankshaft pulley and the camshaft timing gear pulley in the top dead center position. Align the marks on the camshaft timing gear so they are parallel with the top of the cylinder head and the woodruff key is facing up. NOTE: When installing the timing belt, do not allow oil to come in contact with the belt. Oil will cause the rubber to swell. Be careful not to twist the belt unnecessarily or bend in a 90°angle, since it is made with fiberglass; nor should you use tools having sharp edges when installing or removing the belt. Be sure to install the belt with the arrow facing in the same direction it was facing during removal.
  7. After installing the belt, adjust the belt tension by first rotating the crankshaft counterclockwise 1/4 turn. Then, re-tighten the adjusting bolt and finally the tensioner pivot bolt.
  8. Replace the other components removed for belt access.
  9. Start the car, check timing and adjust if necessary WARNING
    Do not remove the adjusting or pivot bolts, only loosen them. When adjusting, do not use any force other than the adjuster spring. If the belt is too tight, it will result in a shortened belt life.

Aug 31, 2010 | 1986 Honda Civic

1 Answer

87 s10 2.5 4 speed wont go into gear ay all new cluch new slave and master cil good can anyone help me


on this particular vehicle you must bleed the system correctly if not you'll keep having this problem you must use a bleeding pump feel the clutch pedal work if this information has be useful please let use know good luck

Jul 28, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

87 chevy s10 4x4 vacuum diagram


NOTE<< If Picture Does Not Show Please Email Me @ rejakwilson@aol.com And I Will Send it to You It IS DETAILED And COMPLETE Diagram of Exactly What You Ask For.

Vacuum and Vapor Hose Diagrams Notes Vacuum Actuation System 42242444

Feb 12, 2009 | 1987 Chevrolet S-10 Pickup

5 Answers

1991 Chevy s10 2.8 5 spd speedometer not working :(


check the fuses, mine did the same thing, I replaced the fuse in the fuse panel and it works great now.. easy fix

Jan 05, 2009 | 1991 Chevrolet S-10

1 Answer

87 S10 Truck Bad Starter or drive pinion.


starter drive probably bad can be replaced

Dec 17, 2008 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...