Question about 2003 Mazda MPV

1 Answer

The two side break lights are no longer working in my 2003 MPV. I replaced bulbs and they are still not working. How do I find out the problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mazda Master
  • 1,075 Answers

The problem is the switch,its located at the back of the brake pedal.get a old rag and wrap it around the pedal and i mean the whole pedal,then get a can of spray oil and spray a little onto the switch.sometimes the button sticks and the oil will realise it,if this fails then replace the switch.please rate this answer.adrian,,,,,,,,,,,,,,

Posted on Aug 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Mazda mpv right side flasher doesn't work but left side does


Have you tried replacing the light bulbs? When a bulb goes bad, the turn signal for that side will usually blink twice as fast as it should. If the bulbs are known to be good, you may want to take a multimeter and test your bulb sockets to be sure you're getting about 12 volts.

Oct 01, 2014 | Cars & Trucks

1 Answer

How to replace little light inside headlight assembly on 03 mazda mpv?


I had one of these vans. They are fantastic for space, but commonly have electrical issues. The head lights are a single unit, and if you want to replace a bulb, the Whole unit has to be removed. There are several screws located on the top and bottom of the unit, that must come out. Then it slides out easily. Replace your bulb/s then reverse.

Aug 29, 2014 | 2003 Mazda MPV

1 Answer

Right turn signal does not work ,flasher works light bulbs work


One of the signal bulbs on the right side is defective and needs replacement or you have a poor electrical connection or connector

Jul 15, 2014 | 1989 Mazda MPV

1 Answer

Rear brake lights not working


break switch above the break are needs to be replaced i think

Nov 21, 2013 | 2003 Ford Mondeo

2 Answers

2003 chevy 1500 rear brake lights not working, but over the cab break light is. bulbs look good, the running lights work.


sounds like a bad turn signal switch . both side brake lights run through it but the third brake l;ight runs direct from the brake light switch .- play with the hazard button a few times and if the start working you need the turn signal switch

Feb 13, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

HEAD LIGHT RETENTION SPRING REPLACEMENT


I just looked at the replace headlamp bulb section, and there are lots of posts with advice. I have done the same as you, and will probably cough up the cash for the shop to fix it.

Mar 03, 2010 | 2003 Mazda MPV

1 Answer

Left tail/break light is not working. replaced


IF NOT THE FUSE IT SHOULD BE A LOOSE EARTH

Feb 27, 2010 | 2003 Jeep Grand Cherokee

1 Answer

How to replace brake light bulb?


If similar to 2002 MPV, you detach the whole side light module, then pop out the bulb-socket, then you can replace the bulb. You need a philips screwdriver, medium size. Open the back hatch. Remove the two screws on the inside edge of the light-assembly. Now pull the whole assembly *sideways* not back - it is held by two detent-pins that face out. You can swing it out a bit and then carefully lever it at top or bottom edge. Lower the assembly face-down, you can see three bulb-sockets. They can be turned a part-turn, I think counter-clockwise, then they pop out. Replace bulb(s), re-insert socket, push assembly back onto pins, replace screws. Just did this for brake/tail light 10 minutes ago.

Oct 26, 2009 | 2003 Mazda MPV

1 Answer

Parking break lights indication


check the level of the brake fluid in the master cylinder

Aug 19, 2008 | 2003 Mazda MPV

1 Answer

How to replace rear break bulb on BMW X5 2003?


1st verify that the brake lights work, if not replace the burnt bulb, if they are ok then the warning module is defective.

Aug 18, 2008 | 2003 BMW 5 Series

Not finding what you are looking for?
2003 Mazda MPV Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...