Question about 2001 Subaru Outback

1 Answer

Car won't start has electricity just replaced starter makes no noise doesn't turn over at all. Also replaced negative battery cable and the battery. Tester shows power to the starter.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

I bet you unhooked the battery when you changed the starter??
now reprogram the car alarm,,,its still on!
have you ever tryed to nick a car with an alarm fitted to it???
they dont start???

Posted on Aug 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car was running, electrical wire burning smell, starter makes grinding noise, with the car running, stop the car, starter keeps making grinding noise, with the car turned off, ABS and trac control


You have the polarity of the battery backward somewhere. Did you replace the starter and hook it up backwards. Difficult but possible. Check your positive and negative on the battery itself.

Nov 23, 2015 | 2001 Mercury Grand Marquis

2 Answers

My car won't turn over, everything works, but doesn't make a noise when I try to start it


Go under the car and see if you have 12 volts at the purple wire to the starter solenoid when the key is held to crank position, the wire may be broken or the starter solenoid is defective.

Jun 08, 2012 | 2001 Pontiac Firebird

2 Answers

Car wont start,seems like battery went dead


If the car doesn't start with a jump you might have a bad alternator. The alternator supplies voltage to the car once the engine is running. If the battery is dead, and the alternator isn't putting out sufficient voltage, the engine cannot run. Then again sometimes a car with an extremely dead or internally shorted battery WON'T start with a jump. Replace the battery and try again.

Dec 22, 2011 | 2002 Hyundai Accent

2 Answers

My car wont start unless it is jumped or push started all the lights come on bright when i turn the key they go dim but the car makes no noise at all i already replaced the battery and its still doing it


Hi, odds are your solenoid has shorted out. Remove the starter and have it tested at your local parts chain. To remove the starter, first remove the negative terminal from the battery, then remove the wires from the solenoid. Then remove the 2 starter bolts--they thread in from the transmission side. See the pics below, and let me know if you have any questions.

jturcotte_2089.gif


jturcotte_2090.gif

Aug 14, 2011 | 1997 Mitsubishi Galant

2 Answers

2003 Kia RIO WHEN TURNED TO ON CAR starts and the starter will not stop turning


Replace the starter.



Removal & Installation

1.5L & 1.6L (VIN 5) Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the 4 upper intake manifold stay bracket bolts.
  4. Disconnect the starter electrical connections.
  5. Remove the upper starter bolts.
  6. Remove the lower starter mounting bolt(s) and the starter.

    0996b43f80207fb6.jpg

    Fig. Starter mounting-1.5L and 1.6L engines


To install:
  1. Install the starter.
  2. Install the lower starter bolt and tighten to 27-38 ft. lbs. (37-52 Nm).
  3. Connect the starter electrical connections.
  4. Install the intake manifold support bracket and finger-tighten the 3 mounting bolts. Tighten the lower bolt to 27-38 ft. lbs. (37-52 Nm).
  5. Install the 4 upper intake manifold stay bracket bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  6. Install the upper starter bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  7. Connect the negative battery cable.

1.6L (VIN 3) Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Air intake assembly Shift cable and bracket Starter electrical connections Starter

To install:
  1. Install or connect the following:

    Starter Starter electrical connections Shift cable Air intake assembly Negative battery cable

May 04, 2011 | Kia Rio Cars & Trucks

1 Answer

My car makes a wierd noise when starting it up


IF ITS MAKING A CLICKING NOISE WONT TURN OVER.CHECK BATTERY CABLE FOR TIGHTNESS AND NO CORROSSION. THE BATTERY VOLTAGE. SHOULD BE 12.5 VOLTS.IF NOT HAVE IT CHARGED AND TESTED.IF ITS GOOD HAVE ALTERNATOR CHECKED OUT.IF BOTH IS GOOD HAVE THE STARTER REMOVED TO HAVE IT AND THE STARTER SOLENOID TESTED.NOTE DUE TO LOCK OUT FEATURE.TURN OFF RADIO SO YOU WONT LOSE CODE WHEN YOU DISCONNECT NEGATIVE BATTERY CABLE.

Aug 12, 2009 | 2004 Dodge Neon

Not finding what you are looking for?
2001 Subaru Outback Logo

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...