Question about 1987 Porsche 944

1 Answer

My clutch doesnt have any pressure, how do i fix that problem?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 25 Answers

Replace your master slave clutch?check for any leaks in the line comgin from the brake resavoir?

Posted on Jan 07, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right steering clutch will not completely disengage. why do i have a loss in pressure when i pull the steering leaver to its travel end?


sounds like didnt get all the trash out --possible valve is fouled or blocked and not closing or sealing correctly and allowing blow by or leakage test valve and pressure piston rings may be causing blow by as well also new parts doesnt mean free from defects

Aug 16, 2016 | Cars & Trucks

1 Answer

Leaking clutch/break fluid


slave cylinder.... clutch fluid doesnt leak from a gear box

Dec 28, 2013 | Cars & Trucks

1 Answer

92 Toyota Pick up clutch doesnt enagage after replacing clutch, and flywheel?


are you sure the driven plate is on the correct side? The clutch bearing is correct on high? Does the slave or master cylinder works ok? do they keep steady pressure when needed? Is the clutch kit the correct part according to engine type?

Nov 12, 2012 | Cars & Trucks

1 Answer

Ac doesnt cool on 02 duramax after new compressor


The compressor should come on at about 32 PSI, so you have either a low charge or a defective fixed orifice or a clogged system.

Aug 24, 2012 | 2002 Chevrolet Silverado 2500HD

1 Answer

2002-v-6,sonata,72,000miles,was told the ac clutch frooze


the ac clutch will quit working if the refrigerant pressure drops too low ... or if the pressure sending switch is bad or if the wire to the clcutch is broken .. the word "frozen" usually means it cant be turned (not that it just doesnt turn) ... if you cant turn the unengaged clutch then thats a compressor failure ... that may in turn damage the clutch as it slips trying to turn the frozen compressor .. if the compressor can be turned freely by hand then thats not the problem .. if the clutch is simply not being turned on then usually thats just low refregerant or a blown fuse, bad relay or bad low pressure switdh . once in a while there might be an open winding on the clutch or a broken wire going to it .. they cant check refrigerant pressure without first getting the clutch to work ... so its possible to jump power directly to the clutch .. it will usually operate and gauges applied to the air conditioner might show the pressure to drop very low .. that would normally turn off the clutch ... just checking for leaks and recharging often is all that is needed ..

Jun 30, 2010 | Hyundai Motor 2002 Sonata

2 Answers

New clutch still slipping


Lets start with what was replaced : Clutch pressure plate, throwout bearing,pilot bearing,input shaft bearing, was flywheel cut or replaced,Clutch cable or slave cylinder (whatever is applicable,) Lets see what repair shop says. Depending on what they say they did or didn't do we will take it from there.
keep me posted

Apr 27, 2010 | 1992 Isuzu Rodeo

1 Answer

No clutch pedal pressure


if you have an adjustable pedal try that and if it still doesnt fix then youll have to replace all the O rings, that dont work then just go to a garage cause it will be cheaper dude then tryin everything

May 11, 2009 | 1984 Toyota Pickup Deluxe

3 Answers

Clutch pedal doesnt spring back up


Have you tried bleeding the clutch. Is it losing fluid?

May 03, 2009 | 1985 Toyota Celica Supra

1 Answer

Clutch


TRY BLEEDING THE HYDRAULIC SYSTEM FOR THE CLUTCH, EASY, FILL CLUTCH MASTER CYLINDER WITH DOT 3 BRAKE FLUID, FOLLOW LINES DOWN NEAR THE TRANS. WHERE CLUTCH PISTON MEETS ATTACH 1/4 CLEAR TUBING TO BLEEDER VALVE RUN HOSE UP TO A BOWL WITH 2" FLUID IN IT, HAVE SOMEONE PULL PEDAL OUT AND PUMP ON IT HOLDING PEDAL DOWN, RELEASE THE VALVE AND CLOSE IT, HAVE THE PERSON PULL OUT ON THE PEDAL AND PRESS IT DOWN AGAIN OPEN VALVE AND CLOSE IT , EVENTUALLY IT WILL BUILD PRESSURE AND GET ALL OF THAT PESKY AIR OUT OF THE SYSTEM, MAKE SURE THE MASTER CYLINDER DOESNT RUN OUT OF FLUID AND THAT THE TUBE DOESNT COME OUT OF THE BOWL OR YOU WILL HAVE TO START OVER, KEEP PUMPING UNTIL THE FLUID RUNS CLEAR WITH NO AIR BUBBLES THIS HAPPENED TO ME LAST WEEK AND NOW IM FIXED AND IT WORKED GREAT! I SUGGEST GETTING A HAYNES REPAIR MANUAL IT REALLY WILL SAVE U ALOT OF MONEY IN THE LONG RUN.

Jul 14, 2008 | 1997 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

896 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...