Question about Honda Passport

1 Answer

Do you have to disconnect the muffler when replacing the starter on a honda passport 2001

Posted by on

  • 1 more comment 
  • capemayor Aug 21, 2010

    is there a special way to disconnect wire from starter. Husband says the plastic might brake

  • capemayor Aug 21, 2010


  • capemayor Aug 21, 2010

    is thee a trick to disconnecting the wiring connectors? afraid we'll break plastic?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 10,515 Answers


The procedure is :-


* REMOVAL & INSTALLATION;Remove or disconnect the following:

Negative battery cable Heated Oxygen (HO 2 S) sensor connectors Exhaust front pipe Heat shield Starter wiring connectors Starter motor . To install:
1. Install or connect the following:

Starter motor. Tighten the bolts to 30 ft. lbs. (40 Nm). Starter wiring connectors Heat shield Exhaust front pipe Heated Oxygen (HO 2 S) sensor connectors Negative battery cable

Good Luck!!


Posted on Aug 21, 2010

  • taran_2005
    taran_2005 Aug 21, 2010

    Thanks for your response!!

    Take a look at :-

    THIS IS FOR 94 MODEL - But, would give you an idea how you need to proceed.

    Any further information, revert and i would be glad to help you.

    Good Luck!!




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001 Honda Passport won't shift into 2nd or 3rd gear. check engine light on

Have vehicle scanned for codes at autozone or similar this will give you an idea what is wrong

Jul 15, 2016 | 2001 Honda Passport

1 Answer

1995 honda passport won't turn over when cold

Your starter solenoid is bad. It comes with a new starter. Replace the starter and your problem should go away.

Nov 16, 2011 | 1995 Honda Passport

1 Answer

Removing starter for 1995 Honda Passport, can I do it myself and what do I need

Very simple job to do for the DIY mechanic, best way to get at the starter is from underneath the car, disconnect the live battery terminal, very important! remove the wiring harness from the starter and undo the three locating bolts that secure the starter to the gearbox, give it a wiggle and it should come free!
Make sure that the live feed off the battery i disconnected! there are some times an engine to bulk head earth starp located on one of the bolts, ensure that this goes back on!
Tool required, 10mm spanner, 13mm sockets etc.

hope this helps

Oct 31, 2009 | 1997 Honda Passport

1 Answer

2001 Passport transmission, rack and pinion replaced at 65K miles

Let's start with some facts. Honda, until 2006, didn't build any "trucks". Your Honda Passport actually began life in the Isuzu Rodeo assembly line. This isn't necessarily a bad thing, just no what you were expecting.
Isuzu makes very reliable trucks, but I think you've just had a run of bad luck. My 95 Isuzu Rodeo was retired after 275,000 miles, but only because some moron rear-ended me very severely, and it wasn't worth repairing, body-wise.
My 5-speed manual needed to be replaced at about 240,000, but the V-6 engine had never been cracked open for any major work. It did, however, have a somewhat loose rack/pinion.

Jun 28, 2009 | 2001 Honda Passport

1 Answer

No power to my starter. 1994 honda passport

The harmonic balancer and starter have nothing in comman... Check all you wire connections all the way to your battery. if all is good have your starter checked..

Apr 17, 2009 | 1994 Honda Passport

1 Answer

Serpentine belt


This is a picture i drew in paint , for the 2001 honda passport belt wrap with a 3.2Liter V6, picture worth a thousand words.

Dec 27, 2008 | 2001 Honda Passport

2 Answers

How do you take the starter off a 1996 honda passport

Yea I know. I hate doing starters in the car. Pretty much its just manuvering it around to get it to slide out. Once you get it disconnected.

It will have three bolts bolting it into the transmission. And then of course the two power bolts.

Dec 15, 2008 | 1996 Honda Passport

1 Answer

Starter noise

could be.
that is the bendix drive of the starter. it is not disengaging.
it will burn the starter if you continue to use it with that noise.

to repair, remove starter and replace bendix drive.

tnx 4 using fixya,


Oct 22, 2008 | 1995 Honda Passport

1 Answer

Repeated Broken Flex Plate in Transmission

1997 Honda Passport 4wd
Make sure you have the correct factory Honda starter in your car , if its an aftermarket starter they may have replaced with cheapo starter,sometime the teeth that engauge starter to your flexplate will not mesh properly,because there different,causing the flex plate to fail. I had the same problem. I went thru 2 before I found this out..Hope this helps.
Please rember to rate me on my help. Thankyou!

Jun 30, 2008 | 1997 Honda Passport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides