Question about 2004 Acura MDX

Open Question

My 2004 MDX Navigation system is not working. It reset itself to the "input code screen". But doesn't do anything after code is put in. I have tried re-installing the disk again, but no luck.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2004 Acrura MDX navigation system goes blank after disclosure.

I had the same problem and carefully cleaning the map DVD solved it. After years of use, a film gets built up on it. It is under the front passenger seat.

Posted on Mar 29, 2009

Ad
  • 1 Answer

SOURCE: MDX 2004 Navigation PIn code does not work

where is the pin code

Posted on Sep 06, 2009

  • 1 Answer

SOURCE: Navigation system is locked up after battery replacement

Found the SN and CODE on the white label attached to the side of the glovebox. SN begins with a "B" followed by 8 numbers. The 4 digit code can be entered into the navigation system to unlock & reset the unit after a power disconnect.

Posted on Sep 23, 2009

  • 1 Answer

SOURCE: 2004 Acura MDX Water Leak

The 2002 MDX I worked on turned out to be a drainage problem . Seems the factory installed foam in the bottom of the hinge pillar post which blocked the drain holes . Take off the mud flap , remove enough of the splash shield to access the bottom of the hinge pillar and drill a half inch hole at the front lower corner aiming the drill slightly upward ( be sure to protect the bare metal) .Water gushed out when I did this. For extra ins. remove the kick panels and check for two holes a few inchs from the floor, plug and chaulk these holes. Hope this worksfor you too

Posted on Jan 07, 2010

  • 3 Answers

SOURCE: Need to reset the code my Acura MDX navigation

check the side of the glove box. my TL has it on the outside side panel as you look from the driver side. my honda prelude had the code there as well. hope this helps

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My navigation system in 2004 mdx has the code screen on but it won't let me put the correct code in. When I touch the 3 the 9 goes up. Screen won't change. What could this be ?


Your digitizer could be shorting out which is why where you touch verses what actually gets picked up is the main issue. There are other issues that can cause it but if your NAV system is embedded into the dash then your best bet is to have it serviced.

May 09, 2016 | Cars & Trucks

1 Answer

Http www vehix411 com


contact a local acura dealership as they should be able to confirm if you have the right code for your vehicle

May 22, 2014 | 2008 Acura Mdx

1 Answer

Need to reset the code my Acura MDX navigation


check the side of the glove box. my TL has it on the outside side panel as you look from the driver side. my honda prelude had the code there as well. hope this helps

Apr 28, 2010 | 2004 Acura MDX

1 Answer

Replaced battery and navigationn propt me to put a code. inputed the code and it shut off.


If you replaced your battery, you probably lost your audio system code as well. You should put that in first or your navigation system voice will not work. I assume you have the code for your audio system.
After you get your audio system working then you should be able to put the code in for you navigation system as follows:
Enter the four-digit navigation system security code, then select Done. If you have entered it correctly, the display changes to the Disclaimer screen. You have ten chances to enter the correct code. If all ten are incorrect, turn the ignition to OFF, then back to ON (II) to have ten more chances to enter the correct code (I would try this is your unit has turned off and doesn't come back on).
If you have other questions on this, leave a comment and I will investigate further.
Hope this helps you.

Nov 18, 2009 | 2006 Honda Accord

1 Answer

Navigation system is locked up after battery replacement


Found the SN and CODE on the white label attached to the side of the glovebox. SN begins with a "B" followed by 8 numbers. The 4 digit code can be entered into the navigation system to unlock & reset the unit after a power disconnect.

Sep 22, 2009 | 2005 Acura MDX

1 Answer

2004 Acrura MDX navigation system goes blank after disclosure.


I had the same problem and carefully cleaning the map DVD solved it. After years of use, a film gets built up on it. It is under the front passenger seat.

Jan 28, 2009 | 2005 Acura MDX

3 Answers

Acura MDX Navigation system is intermittent. Need to remove it to send to Alpine for repair. Can't find instructions.


its really easey to remove the dvd unit under the pasenger seat. just put the seat all the way forward and pull the plastic guard from the seat track (pull straight back) then unplug the harness connectors in the back of the unit.
Then put the seat all the way back and remove the 1o mm nuts on the side brackets of the unit and pull it forward.

Jan 20, 2009 | 2005 Acura MDX

1 Answer

2004 Honda Accord touch screen will not accept code numbers


DOES SYSTEM INTAKE CODE YOU TYPE AND RETURN WITH ERROR MESSAGE OR JUST PLAIN HAS LOCKED SCREEN? SYSTEM IS DESIGNED SO THAT IF INCORRECT CODE IS INPUT MORE THAN THREE TIMES SYTEM LOCKS ITSELF.WHICH REQUIRES THAN THE NAVI UNIT BE UNPLUGGED FROM BATTERY POWER FOR ABOUT 5-10 MINS TO RESET ITSELF.NOW INCORRECT CODE CAN BE DUE TO WRONG CODE/SERIAL # CARD FOR VEHICLE, UNIT HAS BEEN REPLACED IN PAST POSSIBLY AND YOU ARE INPUTING CODE FROM OLD UNIT UNKNOWINGLY. YOU ALSO WANT TO MAKE SURE CODE YOU ARE TRYING TO INPUT IS FOR NAVI-SYSTEM AND NOT THE RADIO CODE FOR THE STEREO. IF ALL ABOVE CHECKS OK THEN NEXT STEP WOULD BE TO REMOVE UNIT TO RETRIEVE SERIAL NUMBER FROM BACK OF NAVI UNIT THEN GO TO NEAREST DEALARSHIP WHO CAN THAN RUN S/N THROUGH HONDA IN SYSTEM AND RETRIEVE CORRECT CODE FOR THAN SERIAL NUMBER. LET ME KNOW HOW IT GO'S

Dec 18, 2008 | 2004 Honda Accord

Not finding what you are looking for?
2004 Acura MDX Logo

Related Topics:

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...