Question about 1999 Pontiac Grand Am GT

1 Answer

Are there grease zerts for ball joints/tierods on a 1999 Grand AM ?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

NO.they are pre lubricated and sealed for life.

Posted on Aug 21, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where are the grease fittings located for 1992 Nissan Sentra E

There are none.
Go to a junk yard or a truck repair garage or a car parts store and ask someone to see a ball joint or tie-rod-end or a grease zert.
They will show you what you are asking for.
There are none on your car.
All the joints on your car are factory sealed.
If a joint wears out, usually after 100,000 miles, it will need to be replaced with a new one, also factory sealed.
Be Blessed.

Jan 21, 2013 | Cars & Trucks

1 Answer

I have a Nissan Hardbody 4x4, when I drive at higher speeds and apply and let throttle the car makes a clacking sound.

check rear driveline u joints soundes like they are dry,might be able to grease if they have zert fitings. if no zerts replace u joints

Dec 16, 2012 | Cars & Trucks

2 Answers

Does the 2000 Lincoln Town Car have grease fittings on the front end?

no they qiut using them in the 2000 model if there any, there on top of the tie rod ends. when they started using struts they got away from grease zerts and ured sealed lower ball joints in 2004 trey also used sealed tie rod ends...A.S.E. CIRTIFIED 30 year mechanic

Feb 15, 2011 | 2000 Lincoln Town Car

1 Answer

Pontiac Sunfire 2004. Where are (if any) grease zerts to grease by my tire rotations?

Okay, if we're talking about a chev 1/2 ton, you have to grease the ball joints, upper and lower. To get the top one you'll probably have to turn the wheel to the left or right all the way, and you will see it on top of the ball joint. The lower ones will either be under the ball joint or sticking sideways. Other than that you have tie rod ends, and you maybe found them already. There may or may not be grease nipples on your u-joints on the drive shaft. Originals are usually sealed, and replacement have nipples. Good luck. Hope this hepls.

Aug 30, 2010 | 1999 Pontiac Grand Am GT

2 Answers

The car is wobbling in the front end, could it be the ball joints or the wheel bearings? 1992 Mercury Grand Marquis.

hi it could be both but its also worth checking wheel balance also engine mounting rubbers hope this helps please rate this answer

Nov 20, 2009 | 1992 Mercury Grand Marquis

1 Answer

Squeak on frontend 4x4 f150 supercrew

usually lower ball ball joints. if they have zert fittings, go ahead and grease them. if they are not there replace the lower ball joints. youll be happier in the long run.

Nov 04, 2009 | Ford F-150 Cars & Trucks

1 Answer

I was told that the grease boots on my 2000 elantra are dry rotted, how do i change them and how difficult is it to do?

what grease boots if its ball jionts or tierod ends you have to replace them(ball joint)//oz

Jul 09, 2009 | 2000 Hyundai Elantra

1 Answer

I have a 2006 chevy colorado crew cab with a body creaking noise when I turn. Sounds like the suspension but I don't think it is.

I had a similar problem, I took grease gun and greased my ball joint, tierod end, and whatever other grease points I saw, and that took care of it. In my case, I think it was the tierod. Grease can go a long way though. Your vehicle is fairly new, but whose to say it wasn't greased enough from the factory. My truck was so annoying, every bump I hit, it sounded like an old bed. Also, sometimes your spring can do that as well. You can throw some WD-40 on that as well for old times sake. Good luck

Feb 25, 2009 | 2006 Chevrolet Colorado

1 Answer

Location of front end grease points?

unless they tie rods and ball joints have been replaced with aftermatkets,Most cars are unserviceable from grease zerts from factory....

Dec 14, 2008 | 1999 Chevrolet Malibu

1 Answer

1999 jeep grand cherokee loredo

Back in the day when grease fittings where installed... Now a days when your lower ball joint needs grease you get new part. WARNING! If Ball Joint Fails loss of control will occour. Part is pressed in control arm. Do have this part checked and have mechanic show you fault.

Aug 19, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides