Question about 1996 Nissan 200SX

1 Answer

Oil pan gasket leaking 1996 Nissan 200sx. How to get to oil pan nuts next to transmission, is a special tool required?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You should be able to access the nuts with a 3/8" exstension with socket

Posted on Sep 26, 2010

  • rodneyklum88 Jan 28, 2011

    do i need to pull the motor or can it be done on jack stands?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i change my oil pan on my 2000 ford crown victoria. There seems to be a welded in crossmember holding the engine underneath do i have to remove the motor mounts and raise the engine to do the oil...


Yes you will have to raise the engine, also, and remove some other items that can be damaged when lifting. An engine hoist will be needed for this job. This text was taken from a 2000 crown vic workshop manual.
see pic for torque sequence. i could not locate a torque spec, so you will have to hand feel them. if it is a rubberized gasket do not over tighten as it will crush the gasket.

Hope this helps!

Rick



Removal

  1. Remove the air cleaner outlet tube.
  1. Remove the wiper arm and pivot shaft assembly.
  1. Remove the drive belt.
  1. Remove the fan motor and shroud assembly.
  1. Disconnect the fuel lines. For additional informatio
  1. Remove the exhaust gas recirculation (EGR) tube.
  1. Remove the generator.
  1. Remove the blower motor speed control.
  1. Raise the vehicle.
  1. Remove the RH engine mount bolt.
  1. Remote the two LH engine mount bolts.
  1. Remove the four nuts and support the exhaust.
  1. Remove the bolt for the transmission line support bracket.
  1. Loosen the nuts for the transmission mount.
  1. Lower the vehicle.
  1. NOTE: The RH motor mount has a second bolt accessed from the top.Remove the bolt.
  1. Using the special tool, raise the engine with a suitable floor crane.
  1. Using the special tool, support the engine.
  1. Raise the vehicle.
  1. Remove the oil pan bolts.
25293938-y12x0o0o0lm2kgfxdyqglnjp-2-2.gif
  1. Position the oil pan aside and remove the bolts from the oil pickup tube.
  1. Remove the bolt from the oil pickup tube bracket.
  1. Remove the O-ring and inspect.
  1. Remove the oil pan and gasket from the vehicle through the front.
Installation
  1. Install the oil pan and gasket on the vehicle.
  1. Install the O-ring, using a new one if necessary.
  1. Position the oil pickup tube and tighten the bolts.
  1. Install and tighten the bolts.
25293938-y12x0o0o0lm2kgfxdyqglnjp-2-0.gif
  1. Lower the vehicle.
  1. Using the special tool, and a suitable floor crane, raise the engine and remove the special tool.
  1. Remove the special tool.
  1. Lower the engine
  1. Remove the special tool.
  1. Raise the vehicle.
  1. Tighten the nuts.
  1. Install and tighten the bolt.
  1. Reposition the exhaust and tighten the nuts.
  1. Install and tighten the bolts.
  1. Install and tighten the bolt.
  1. Lower the vehicle.
  1. Tighten the bolt.
  1. Install the blower motor speed control.
  1. Install the generator.
  1. Install the EGR tube.
  1. Connect the fuel lines.
  1. Install the air cleaner outlet tube.
  1. Install the wiper arm and pivot shaft assembly.
  1. Install the drive belt.
  1. Install the fan motor and shroud assembly.

Nov 23, 2014 | 2000 Ford Crown Victoria

2 Answers

No reverse after i park my 1962 ford automatic


Fluid level and a dirty filter are the first things to check, then a band adjustment is next on the list. as the pan needs to come off to change the filter adjst the bands at the same time. the tea levels in the bottom of the oil pan will tell you in there are more serious issues inside.

Terry

Nov 25, 2012 | Cars & Trucks

1 Answer

1996 nissan maxima oil leak on passenger side


You should try your oil pan gasket or your timing chain gasket cause that I'm taking mine to the shop to see what it is exactly buy I don't have the time to look at the leak exactly ill let you know what it is exactly though ok.

Apr 29, 2012 | 1996 Nissan Maxima

1 Answer

Cannot remove the passenger side axle on a 1996 200sx Nissan


if you mean the transmission end ! put a pan under transmission to catch the fluid. use a bar, or big screwdriver to pry axle out of transmission. when putting back in, make sure the axle snap ring is tightly locked in transmission.

Nov 05, 2011 | 1996 Nissan 200SX

1 Answer

Leaking transmission fluid


TRANSMISSION FLUID LEAKS,CAN BE FOUND AROUND PAN GASKET.CHECK PAN GASKET,IF IT LOOKS WET AND YOU SEE FLUID DRIPPING AROUND THE EDGE OF OIL PAN, REPLACE PAN GASKET, WHILE YOU REPLACING PAN GASKET REPLACE TRANSMISSION FILTER WHILE OIL PAN OFF.IF TRANSMISSION OIL PAN NOT LEAKING, CHECK TRANSMISSION OIL COOLER LINES GOING INTO RADIATOR YOU WILL LOOSE A LOT OF FLUID THERE ALSO TORQUE SHAFT SEAL WILL CAUSE HEAVY FLUID LEAK WHILE ENGINE RUNNING CHECK OIL COOLER LINES AND LOOK AT THE TORQUE AREA WHILE ENGINE RUNNING YOU WILL SEE FLUID POURING WHILE ENGINE RUNNING THE OIL PUMP PRESSURE WILL PUSH FLUID OUT AT THE LEAKING AREAS.

Aug 01, 2011 | 1991 Nissan Stanza

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

1 Answer

Can you walk me trhu the transmition fluid change im going to chenge the transmition fluid my self


This job requires some special tools first a swivel to get to the pan bolts and you have to remove all nuts off the oil pan on the transmission. you will need a pan to pick up 4 quarts of fluid that will come out when you loosen the oil pan, next after you hav all the nuts out use a pat scraper and a hammer and tap around the edge of the pan to get the pan loose, next once the pan is off unbolt the screen from the transmisson housing, Next drop the pan and then remove the filter remoce the filter oring and install new one from the kit you bought. clean bolts out then put the bolts in the holes and screw then in so you can install pan back on without the gasket falling off, after filter is in place and screwed on screw on the oil pan for the transmission go from right to left and front to back one bolt at a time tighten lightly till all bolts are snug. next undo the treansmisson line on the bottom of the radiator seperate the line and start the motor put it in drive with emergency brake on then put in low gear and allow 3 quarts of oil to drain out of transmission,, shut off motor and add 5 quts of ATf dexron 2 or dexron III EATIER WILL WORK . next with line still loose run three more quarts out, it will take about 12 quarts to change all trasnmisson fluid to change out all fluid also add one quart of lucas transmisson condtioner this will make the transmison shift smother and soften band and seals put the line back on the oil cooler on the radiator then start the car in park check for leaks, if you see no leaks then at idel check fluid level it should not be less than a pint low or a pint high it will cause problems. if you add to much loosen the line and let some run out then tighten and you check the fluid again if it's to the top you done. test drive after done this will take about 4 hours doing it this way good luck on your job.

Aug 17, 2010 | 2000 Ford Windstar

1 Answer

Trying to remove oil pan from 1989 chevy 1500 350 eng to replace the gasket can you help me?


2wd Models
  1. Disconnect the negative battery cable. Drain the engine oil.
  2. Remove the oil dipstick.
  3. If necessary remove the exhaust pipe crossover.
  4. If equipped with automatic transmission, remove the converter housing pan and the transmission oil cooler line retainer from the bracket.
  5. On 1996-98 models, remove the oil filter and if equipped, the oil filter adapter.
  6. If necessary, remove the starter brace and bolt and swing the starter aside.
  7. Remove the strut rods, if equipped.
  8. Remove the oil pan and discard the gaskets.
To install:
  1. Apply a suitable sealant such as GM part number 12346192 or its equivalent to the front cover-to-block joint and to the rear crankshaft seal-to-block joint. Apply the sealant about 1 inch (25mm) in both directions from each of the four corners.
  2. Clean all gasket surfaces and use new gaskets to assemble.
  3. Install new gasket and seals.
  4. Install the oil pan.
  5. On 1988-95 models, tighten the pan bolts to 100 inch lbs. (11 Nm). Tighten the pan nuts to 17 ft. lbs. (23 Nm).
  6. On 1996-98 models, tighten the oil pan nuts and bolts to 18 ft. lbs. (25 Nm).
  7. Install the strut rods, if equipped.
  8. If removed, install starter, starter brace and bolt.
  9. If equipped, install the oil filter adapter.
  10. If removed, install the oil filter.
  11. If equipped with automatic transmission, install the converter housing pan and the transmission oil cooler line retainer to the bracket.
  12. Install the exhaust pipe crossover.
  13. Install the oil dipstick.
  14. Fill the engine with oil and check for leaks.

Aug 07, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

Think I need oil pan gasket


It's probably the front crank seal or the cam seal. Kinda big job for a novice. The car only has one oil pan. The back one she refered to is for the transmission,if it's automatic. Never saw a oil pan gasket leak on a nissan '96 & up.

Jul 14, 2009 | 2000 Nissan Altima

1 Answer

Transmission oil is leaking on 96 5.2 v8...where


THE MOST COMMON LEAKS ARE THE TRANS FLUID PAN GASKET, THE NEXT IS THE TORQUE CONVERTER FRONT SHAFT SEAL.

Jul 12, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Nissan 200SX Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...