Question about 1998 Ford Explorer

1 Answer

How do you replace a break light? - 1998 Ford Explorer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

Remove the taillight assembly. If I remember correctly, you have to open the door to get to the screws.

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my brake light fuse?


The break light have a fuse in the fuse box. If this blows then both break lights will go out. Its usually under the hood in the fuse box or its in the panel on the right or left inside where the front doors close. Some cars have a fuse box under the steering column. If this is not the problem then it may be a break light switch. These are located just up the break petal. Its a switch that gets released when the break is pushed with your foot.

Jul 16, 2014 | 2005 Chrysler Sebring Sedan

1 Answer

1993 GMC sierra 1500 replaced rear turn signal bulb and break light bulbs..still no break light and turn signal still flashing fast..no hazzard light on same side


the break switch is damaged replace it then the hazzad light and the break light will be ok .. and about the indicator light its circuit's capacitor or the resistor is damaged please check that and replace the same it will be ok

Aug 24, 2012 | Cars & Trucks

1 Answer

Tail lights work but break lights do not work


Chack the break light switch which on my car is on the break tank. There should be 2 wires going to the switch. If you short them out and the lights work then replace break light switch.
It might be the earth connection to break lights. If there is an earth lead remove clean and replace.Then give the connection a coat of paint.

Mar 15, 2012 | 1999 Lexus RX 300

3 Answers

The break lights won't light when i push the breaks but they work for every thing else like 4ways turn signal but when i go to stop they dont light up i replaced the switch and the bulbs but still dont...


When you replaced the brake light switch did you adjust it so that it contacts when it should?
It isn't enough to just replace it, you need to adjust the pedal height to specifications in order to make the brake lights work correctly.

Sep 11, 2011 | 2000 GMC Jimmy

2 Answers

No break lights ,tail lights on a 1999 suberban check the fuse and they are all good when i turn my lights on and put on the turn singal and press on the break they start blinking very fast when i thouch...


it sounds like a ground problem...sounds like the ground is trying to go through the bulbs to make connection....check all ground wires battery, engine and rear frame...

May 27, 2011 | 1999 GMC Suburban

1 Answer

98 mercury villager breake light


There may be an adjustment on the switch, not sure, but hope it helps a little

May 25, 2009 | 1998 Mercury Villager

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

1 Answer

Break lights


welcome to fixya

there is a break switch under the dash connected to the break itself once you press the break the switch trips and the lights go on it sounds like that switch is gone you need to replace

hope this helps you out have a good day

Jul 11, 2008 | 1995 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...