Question about 2005 Nissan Frontier

Open Question

Failed canister vent solenoid on 2005 frontier

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

  • 37 Answers

SOURCE: HAVE A TROUBLESHOOTING MESSAGE PO446

DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Posted on Dec 06, 2008

csmock132
  • 4669 Answers

SOURCE: check engine light continues to be lit.

What code number do you have or do you have 3?

Posted on Mar 25, 2009

  • 1 Answer

SOURCE: I have a 2006 Chevy

***IMPORTANT INFORMATION YOU MUST READ*****

Ok everyone, listen up....If you have a 04 and newer silverado, with a failed evap vent solenoid, you have to read this info. Do not pay $100+ for this part(actually $150.00 at the dealer). The following part numbers associated with this part have been gm#19207763,19152349, and AC DELCO #'s 214-2082 costing over $100.00 for the modified part. This is for the modified part, with the relocation of the filterbox, and the added hose that seperates the two. No one at Gm will tell you this, but this same part, that was origionally on your silverado, is also used in the 2006 Suburban. It will be an identical replacement for what is ON YOUR TRUCK, and the cost is $24.04 AT THE DEALER. I know this because I own a 2006 silverado, and a 2006 suburban. Looked at the suburban when the part went bad on the silverado(from overfilling the tank)and bingo, same part. Ask a parts person at GM, and they will tell you otherwise, but they are lying to you. Bought the suburban part today part # 25932571 (GM #) and everything is identical, right down to the numbers stamped on the part itself. Took the part off my silverado, put the replacement on (which gm told me is not the right part), cleared the codes, and bingo no more light after 3 consecutive starts...... Why, is it that GM feels we need to pay the price for something they did wrong???? And moreso, lie to us, telling us the $150.00 part is our only choice to fix the problem. My truck went 40K miles with the origional part, and probably only went bad because of my own stupidity in overfilling the tank, whay would I not just want to spend $24.00 to put on the same part, that will probably go the rest of the life of the truck with no tank overfills???? I say CLASS ACTION LAWSUIT FOR EVERYONE THAT HAS BEEN SCAMMED INTO PAYING THE RIDICULOUS PRICE that GM is trying to **** out of us.....Please pass this on to the world, and every forum you can...Get the word out....Let the parts people at GM know we are on to their BS, and they can't take advantage of us like they have.....

Posted on Aug 11, 2009

johnjohn2
  • 5763 Answers

SOURCE: What does failed canister vent solenoid mean on my

it a sealed system that take gas fumes and bruns them threw the engine to lower emmision into the air.there a valve in the system as like the canister is anonther part that filters,but anyway the vent valve vents preasure or vapors if its no working system cant seal or vent when it needs to,hope this helps.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does code po499 mean on my 2003 dodge 2500


Trouble Code: P0499

NVLD Canister Vent Solenoid Circuit High

Possible Causes:


NVLD canister vent solenoid control circuit is open or is shorted to power.NVLD canister vent solenoid ground circuit is open.NVLD canister vent solenoid is damaged or it has failed.PCM has failed.Mr. Perkins,here are the causes for the code.

Nov 28, 2012 | Cars & Trucks

1 Answer

How do i fix a 0446 code on a 2000 nissan frontier. ext cab 4x4 3.3l vs manual trans


The evaporative emission control system checks to make sure there are no leaks in the lines that run from the gas tank to the charcoal canister and up to the engine. It also checks to make sure the gas cap is sealing correctly.
When you fill your car with gas, the vapors in the tank get forced into a canister filled with activated charcoal. Also, on a hot day as the gas heats up and vaporizes, those same vapors push into the canister where they're stored. But the charcoal can only hold so much vapor. At some point it has to be emptied. The emptying process is called "canister purge." Here's how it works.
The computer orders a canister purge by powering open a purge solenoid. That opens the vacuum line between the canister and the intake manifold. At the same time, it opens a VENT solenoid. That allows fresh air into the canister. So the engine is literally sucking out the gas vapors and purging the canister with fresh air. The computer has to adapt its fuel strategy to take advantage of all the extra gas vapors coming into the engine.
The computer notices the canister is empty when it detects a leaner condition (all the vapors are used up) and it resumes normal fuel delivery. Some car manufacturers then close the VENT solenoid but leave the PURGE solenoid open. That creates a vacuum throughout the entire fuel storage system. Once the correct vacuum is reached, it closed the PURGE solenoid and waits to see if the vacuum holds. If it doesn, the system passes the test. If it detects a leak, it sets a code.
The computer also watches the electrical activity during the testing process. When the computer operates the solenoids, it sees a voltage drop on the line. If it doesn't see a voltage drop, it knows there's a problem with the electrical--either the wiring is broken, or the solenoid isn't working. In this partcular code P0446, the computer has detected an electrical problem with the VENT solenoid.

Mar 08, 2011 | 2000 Nissan Frontier

1 Answer

What is p1451? and how do i fix it


Technical Description:
EVAP Control System Canister Vent Solenoid Circuit Malfunction
The EVAP system monitors the canister vent (CV) solenoid circuit for an electrical failure.
The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
Symptoms: You will likely not notice any drivability problems.
Causes: A code P1451 may mean that one or more of the following has happened:
*VPWR circuit open
*Damaged canister vent solenoid
*Canister vent solenoid circuit open or shorted to ground, power, etc.
*Damaged Powertrain Control Module (PCM)
*Possible SolutionsVerify canister vent solenoid - To verify normal functioning, monitor the EVAP canister vent solenoid signal PID EVAPCV and the signal voltage
(PCM control side).With the valve open, EVAPCV indicates 0% duty cycle and a voltage approximately equal to battery voltage.
When the valve is commanded fully closed, EVAPCV indicates 100% duty cycle, and a minimum voltage drop of 4 volts is normal.
Output test mode may be used to switch output on/off to verify function.
*Replace canister vent solenoid

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 29, 2010 | 1997 Ford Taurus

1 Answer

My 2005 Tahoe has engine light codes P0449 & P0455. What should I replace first?


The PCM has determined that a malfunction exists in the electrical circuit for the vent valve/solenoid in the evaporative emission control system.


Probable Causes
1- Purge or vent solenoids defective
2- Check connevtor and wiring
3- Fuel saturated vapor canister
4- Failed EVAP vent solenoid

Aug 24, 2010 | 2005 Chevrolet Tahoe

1 Answer

What does: "Diagnostic Trouble Code: P1451 Manufacturer Specific Code" mean on a 1999 Mazda B3000. I failed an emissions test due to this code.


Technical Description:
EVAP Control System Canister Vent Solenoid Circuit Malfunction
The EVAP system monitors the canister vent (CV) solenoid circuit for an electrical failure.
The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
Symptoms: You will likely not notice any drivability problems.
Causes: A code P1451 may mean that one or more of the following has happened:
*VPWR circuit open
*Damaged canister vent solenoid
*Canister vent solenoid circuit open or shorted to ground, power, etc.
*Damaged Powertrain Control Module (PCM)
*Possible SolutionsVerify canister vent solenoid - To verify normal functioning, monitor the EVAP canister vent solenoid signal PID EVAPCV and the signal voltage
(PCM control side).With the valve open, EVAPCV indicates 0% duty cycle and a voltage approximately equal to battery voltage.
When the valve is commanded fully closed, EVAPCV indicates 100% duty cycle, and a minimum voltage drop of 4 volts is normal.
Output test mode may be used to switch output on/off to verify function.
*Replace canister vent solenoid

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question&&&&

May 26, 2010 | 2007 Mazda B3000

1 Answer

Nissan frontier 2002 failed emissions test with code P0447 something to do with service engine soon light. how do i fix this?


CODE PO447 EVAP CANISTER VENT CONTROL VALVE CIRCUIT OPEN.POSSIBLE CAUSES. 1.HARNESS OR CONNECTORS THE SOLENOID VALVE CIRCUIT IS OPEN OR SHORTED. 2. EVAP CANISTER VENT CONTROL SOLENOID VALVE.

Jan 07, 2010 | 2002 Nissan Frontier Crew Cab

1 Answer

ENGINE CODES OF 200c, 242f and P1451


Technical Description:
EVAP Control System Canister Vent Solenoid Circuit Malfunction
The EVAP system monitors the canister vent (CV) solenoid circuit for an electrical failure.
The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
Symptoms: You will likely not notice any drivability problems.
Causes: A code P1451 may mean that one or more of the following has happened:
*VPWR circuit open
*Damaged canister vent solenoid
*Canister vent solenoid circuit open or shorted to ground, power, etc.
*Damaged Powertrain Control Module (PCM)
*Possible SolutionsVerify canister vent solenoid - To verify normal functioning, monitor the EVAP canister vent solenoid signal PID EVAPCV and the signal voltage
(PCM control side).With the valve open, EVAPCV indicates 0% duty cycle and a voltage approximately equal to battery voltage.
When the valve is commanded fully closed, EVAPCV indicates 100% duty cycle, and a minimum voltage drop of 4 volts is normal.
Output test mode may be used to switch output on/off to verify function.
*Replace canister vent solenoid

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^^^^

Dec 11, 2009 | 2008 Dodge Ram Pickup 3500

1 Answer

Hi my 2005 Chevrolet Tahoe seems to have a blocked fuel vent .When I try to fill it I can hear a whistling and the fuel keeps backing up in the filler neck . Do yoy have any drawings for the routing or...



There may be a problem with your EVAP system.Dirt/dust can get into the system causing a poor fill condition.Replacement of EVAP canister and or vent solenoid may be required.
The canister and vent solenoid are located near the gas tank on the passenger side under the vehicle.


• Fuel fill limiter vent valve stuck closed • Evaporative emission (EVAP) canister restricted • EVAP vent valve stuck closed • Hose between canister and canister vent solenoid twisted or kinked if applicable • High fuel temperature • Fuel filler hose is kinked

Nov 01, 2009 | 2005 Chevrolet Tahoe

2 Answers

Engine trouble code 0499 2004 dodge dakota manual 5 speed 4.7 4x4


P0499 Evaporative Emission System Vent Valve Control Circuit High, REPLACE THE SOLENOID.

Jun 24, 2009 | 2004 Dodge Dakota

Not finding what you are looking for?
2005 Nissan Frontier Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...