Question about 1999 Chevrolet Silverado 1500

1 Answer

I need to take the door panels off on a 1999 Silveraldo to replace door speakers.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 389 Answers

Hello my name is Ben and I can help you with this. Look toward the front bottom and remove that screw, then there is one at the armrest. If power windows, carefully pry the switch assembly up and disconnect electrical connectors. If manual windows, there is a clip shaped like a " C " that holds the handle on a grooved shaft shaft. You can either buy a special tool to remove the clip or use a very thin screwdriver and pry it off from behind the crank handle. It helps to push the door panel in slightly to gain access to the back of the crank handle. CAUTION, the C clip has a tendency to fly off into outer space never to be seen again. Carefully pry out the trim piece around the door handle. Next remove that triangle shaped plastic piece at the top of the door trim, it just comes straight out, ( use a small screwdriver or putty knife to gently pry it out from the edge ) , once you are sure you have found all the screws, start at the bottom of the panel and pry it out, when the fasteners are out lift the panel up.If you meet STRONG resistance double check for any screws you missed. If you have any questions about this feel free to leave a comment and I will try to clarify my answer, Ben.

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace door panel bulb c1500/1966/silverado


You have this listed under a 1999 c1500... so if you are wanting info on a 1966 model (see 1966 in there) you;re in the wrong place.
For a GREAT video showing you everything, I've included a link to show you step by step. It is aimed for speaker replacement, but all goes to taking it loose so you have access to lights (I replaced speakers and lights at same time since one light was burnt out).
I haven't watched vid to the end (since no back lights) but bet he won't cover taking rear no-door panel loose - lol, I never did get that all the way off and squeeezed the speaker in.

Jul 14, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do i remove my 1999 toyota camary door speakers??


Remove the door panel and you will have access to the
speaker. The door panel has a couple of screws in the middle and
a couple on the bottom.

Nov 01, 2010 | 1999 Toyota Camry

1 Answer

Door panel and bezel removal


There are two screws in the door pull (which face straight down) - remove those first.

Next remove bezel around inside door handle. Carefully use screwdriver to push in on four tabs (at the four compass headings) and pull out on bezel. These are easy to break as they get brittle with age.

Start at bottom of door (using a trim removal tool) and pry out door fasteners (white posts which fit into friction fittings in door). You have to pry pretty hard. Use trim removal tool to apply force right at fastener. There are 3-4 on bottom of door and two on each side.

Once all the fasterners are loose. Carefully look behind door and remove the doors light and speaker connectors. The Speaker Connector can be hard to get to - you may need some help holding panel. Be careful because the wires to speakers are delicate and easy to break.

Once the panel is loose - roll down windows and pull up on door panel. It has a lip that fits over top of the door opening. You must pull straight up to disengage it.

That's it all done - not really hard but will seem a little strange at first. Take your time and be careful and the seconds one will take much less. I've had to remove all four of my door panels on my 1999 K1500 to replace window and lock motors. But, after 200,000 miles the 'burb is going strong.

Feb 12, 2010 | 1999 GMC Suburban

1 Answer

1999 chevrolet suburban: door panel removal


hello here is the instructions for removing the door panel.

  • Remove the door handle bezel.
  • Remove the window handle,.
  • Remove the power accessory switch panel.
  • Remove the trim panel upper extension
  • Remove the trim panel screws.




  • Remove the courtesy light,
  • Remove door panel screws.
  • Remove the trim panel from the door, carefully sliding the trim panel up to release the retainers from the door.
  • Remove the speaker wire.
  • 3470484.gif

    Jan 23, 2010 | 1999 GMC Suburban

    3 Answers

    99.5 Jetta Interior Noise


    If the door panel has never been removed then it could possibly be a bad speaker.

    Being a 99 model it could also have a plastic liner under neath the door panel that has dry rotted and needs to be removed.

    I'd place my wager on the speaker though.

    If the panel has been removed check to make sure that you don't have any broken clips that attatch your door panel to the door.

    Apr 02, 2009 | 1999 Volkswagen New Jetta

    2 Answers

    Drivers door glass replacement 1999 ford contour


    The first thing that you need to do is Go to the Auto Parts Store and get some Door Panel Fasteners for your car. You will Break a Few in the Repair. Next, Try and Locate ANY Screws or False Screw Hole Fillers in the Door Panel. Once you have found these Start at the Bottom of the Door Panel and slowly Pull it Off. Once you get it off, Clean out the Track that the Window Sits in with a screw Driver. Put some Clear Silicone Sealant into this Track and Insert the Window from the Top. Press Firmly into the Track and Slowly Raise the Window all the way up. Allow 24 Hours or so for the Sealant to Dry before Opening the Window.

    Jan 23, 2009 | 1999 Ford Contour

    1 Answer

    How do you replace the front door speakers in a 1999 Model Hyundai Excel?


    You have to take the door panels off.
    The front speakers are 6"
    So remove the front door panels, unbolt the factory speakers, bolt the new one in the existing holes, reinstall the door panels.
    The grills will look factory, but you will have better speakers. Nice way to keep the good stuff hidden from prying eyes.

    Oct 19, 2008 | 1994 Hyundai Excel

    1 Answer

    Removing the front door panel


    there a special tool to remove that clip or you can use a women nylon slip the nylon beetween the handle and door panel and move it be carefull that clip fly off when it loose thanks pierre

    Oct 08, 2008 | 1999 Chevrolet Malibu

    Not finding what you are looking for?
    1999 Chevrolet Silverado 1500 Logo

    113 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...